Maximum; 20% to 80% x VDD; Output load (CL) = 4 pF
Worst case; For frequencies ≤ 100 MHz;
Worst case; For frequencies > 100 MHz;
Output valid time after VDD meets the specified range & STBY# transition
Output load (CL) = 4 pF; 75 MHz
Output load (CL) = 4 pF; 75 MHz; measured over 12 K cycles
Conditions
Note: Above specifications are typical at room temperature (25°C ) unless otherwise specified.
* Inclusive of initial frequency accuracy, operating temperature range, supply variation, load variation, 3 times solder reflow, shock, vibration and 10 years aging at 25°C.
may cause permanent damage to the device. These ratings are
stress specifications only. Functional operation of product at
these or under any condition beyond those listed in the
operating specifications is not implied. Exposure to absolute
maximum rated conditions may affect product reliability.
Item
VDD
STBY#
OUT
Storage Temperature
Solder Reflow Profile
40 sec (max)
250
200
150
100
50
150°C
60-180
sec
(260°C max)
245°C
217°C
c
/sec
°
/
6
°
C
60-150
sec
a
ma x
4.6 V
-0.5 V to VDD + 0.5 V
-0.5 V to VDD + 0.5 V
-65°C to 150°C
3
°
C/
se
Maximum Absolute Rating
cm
ax
Time
Pin Descriptions
Pin #
1
2
3
4
Output Waveform
1
Name
STBY#
GND
OUT
2
VDD
Description
0.8 VDD
0.5 VDD
0.2 VDD
T
R
T
F
V
OH
Standby Mode (0 = Output Disabled)
Ground
CMOS Output
Power
1. Pulled high internally
2. Weak pull down to GND during STBY# enable and startup
V
OL
SYM = t
1
/ t
2
t
1
t
2
Time
Ordering Information
3DN11G
Frequency
4 to 133MHz
4.09600
22.5792
133.000
NSG
I
8
Package
Suffix
Minimum Order Quantity (MOQ)
T&R
Bulk
2500
3000
1260 (18 Tubes)
1250 (Canister)
Factory Order Increment (FOI)
T&R
Bulk
2500
3000
1260 (18 Tubes)
1250 (Canister)
Package
NSG: 5.0 x 3.2 x 0.85
NVG: 2.5 x 2.0 x 0.55
Shipping
Blank: Tubes
8:
Tape and Reel
NSG
NVG
6024 Silver Creek Valley Road
San Jose, California 95138
Sales
800-345-7015 (inside USA)
+1 408-284-8200 (outside USA)
Fax: 408-284-2775
Technical Support
crystalfreetechsupport@idt.com
+1 408-360-5656
DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document,
including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not
guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the
suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any
license under intellectual property rights of IDT or any third parties.
IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an
IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.
Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective
