19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
L
L
ASSEMBLY
PART NO.
TPA
PART NO.
CONNECTOR
HOUSING NO.
TERMINAL HOUSING
PART NUMBER
COLOR
BLACK
LIGHT GRAY
KEYING
OPTION
NUMBER OF
PLUGGED
POSITIONS
CAVITY STATUS (X = PLUGGED)
1
2
3
4
TOOLED
34511-1001
K
34514-0001
34514-0002
34514-0003
34514-0004
34514-0001
34512-0003
34512-0003
34512-0003
34512-0003
34512-0001
34513-0001
34513-0002
34513-0003
34513-0004
34513-0001
A
B
0
0
0
0
2
X
X
X
(4.8)
(1.6)
(1.6)
(4.8)
K
34511-1002
34511-1003
34511-1004
34511-1011
BROWN
DARK GRAY
C
D
BLACK
A
X
J
J
KEYING OPTION A
KEYING OPTION B
KEYING OPTION C
KEYING OPTION D
H
H
CAVITY ID
CONNECTOR HOUSING
BLACK
SEE CHART
G
SEE NOTE 6
TERMINAL
POSITION # 4
TERMINAL
POSITION # 1
G
(1.10)
MATTE SEAL
LIGHT BLUE
34516-0001
(0.50)
(32.2)
TPA IN PRE-LOCK
SEE NOTE 4
LOCATION
CODE
REAR VIEW
(WIRE HARNESS SIDE)
F
F
TERMINAL HOUSING
SEE CHART
PERIMETER SEAL
GREEN
34515-0001
TPA
NATURAL
SEE CHART
DETAIL Z
SCALE 20:1
4.00
NOTES: UNLESS OTHERWISE SPECIFIED.
E
(
⌀
27.50MIN
PASS-THRU )
PART NUMBER
DATE CODE
E
1. MATERIAL
PLASTIC: GLASS FILLED SPS RESIN
SEALS: SILICONE
2. FOR RECEPTACLE TERMINAL TO BE USED WITH THIS ASSEMBLY
SEE MOLEX DRAWING SD-33468-001.
TERMINAL BOX AND CRIMP SHOULD BE PARALLEL TO EACH OTHER
WITHIN ONE DEGREE (1
°
) TO PREVENT TERMINAL STUBBING.
D
SEE DETAIL Z
(17.89)
3. DESIGNED TO MATE WITH HIRSCHMANN DRAWING 872-975-XXX
VARIANTE 1 WITH FORM 1 BLADES ON DRAWING 1 99 51 50733 1.
4. ASSEMBLY SHIPPED WITH TPA IN PRE-LOCK POSITION.
EACH TPA MUST BE SNAPPED INTO FINAL LOCK
POSITION UPON FULL TERMINAL ASSEMBLY.
5. SYSTEM TO BE USED WITH SAE 18 AWG, 20 AWG AND 22 AWG WIRES
WITH DIAMETERS IN THE RANGE OF 1.5 MM TO 2.13 MM.
(28.7)
TPA IN FINAL LOCK
SEE NOTE 4
D
(25.5)
TRACEABILITY MARKINGS
C
6. TO PREVENT TERMINAL BEAM DAMAGE, USE RECTANGULAR
FLAT TIPPED PROBES FOR TERMINAL PROBING.
7. TPA FORCES
A. ENGAGEMENT FORCE - WITH TERMINALS (PRE-LOCK TO FINAL-LOCK): 70 N MAX
B. DISENGAGEMENT FORCE - WITH TERMINALS (FINAL-LOCK TO PRE-LOCK): 15N MIN
8. FOR RECYCLING INFORMATION CONTACT MOLEX.
C
SYMBOLS
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
DIMENSION UNITS
SCALE
CURRENT REV DESC:
mm
ANGULAR TOL
±
±
±
±
±
±
2:1
B
°
B
9. SHALL CONFORM TO THE FOLLOWING PACKAGING SPECIFICATION NUMBER: PK-31300-163
10. FINISHED ASSEMBLIES TO BE MARKED WITH DATE CODE AND PART NUMBER.
11. TPA'S MAY BECOME SEATED DURING TRANSIT. IF THIS OCCURS, TPA'S SHOULD BE
MOVED TO THE PRE-LOCKED POSITION PRIOR TO FEMALE TERMINAL INSTALLATION.
12. FORCE TO BE APPLIED TO SECONDARY LOCK FOR CAVITY DAMAGE SUSCEPTIBILITY
TESTING (USCAR 5.4.9) TO BE 60 N.
GENERAL TOLERANCES
(UNLESS SPECIFIED)
EC NO:
604499
4 PLACES
3 PLACES
2 PLACES
1 PLACE
0 PLACES
A
DRWN:
HKLIANG
CHK'D: JDENG02
APPR:
JDENG02
INITIAL REVISION:
DRWN:
BFLOWERS
APPR:
SMARCEAU
THIRD ANGLE PROJECTION
DRAWING
2018/09/17
2018/09/19
2018/09/19
2004/04/12
2004/04/13
SERIES
CONNECTOR ASSEMBLY
4 CKT 1.2 MM SEALED
PRODUCT CUSTOMER DRAWING
DOCUMENT NUMBER
DOC TYPE
DOC PART
REVISION
SD-34511-001
MATERIAL NUMBER
CUSTOMER
PSD
001
L
A
DOCUMENT STATUS
FORMAT: master-tb-prod-D
REVISION: H
DATE: 2018/01/18
P1
18
RELEASE DATE
17
2018/09/19
16
21:01:15
15
14
13
12
11
10
9
8
C
=
0
7
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
SHEET NUMBER
D-SIZE
5
34511
4
3
GENERAL MARKET
2
1 OF 1
1
19
6
51单片机
