JTAG
series
SIGNUM SYSTEMS C ORPORATION
JTAG Probes for Signum Emulators
Technical
Specifications
COPYRIGHT NOTICE
Copyright (c) 2012 by Signum Systems Corporation, an IAR Systems company. All rights are reserved worldwide. No part
of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise, without the prior written permission of Signum Systems.
DISCLAIMER
Signum Systems makes no representations or warranties with respect to the contents hereof and specifically disclaims any
implied warranties of merchantability or fitness for any particular purpose. Also, Signum Systems reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of Signum
Systems to notify any person or organization of such revision or changes.
WARRANTY
Signum Systems warrants to the original purchaser that this product is free of defects in material and workmanship and
performs to applicable published Signum Systems specifications for a period of SIX MONTHS from the date of
shipment. If defective, the product must be returned to Signum Systems, prepaid, within the warranty period, and it will
be repaired or replaced (at our option) at no charge. Equipment or parts which have been subject to misuse, abuse,
alteration, neglect, accident, unauthorized installation or repair are not covered by warranty. This warranty is in lieu of any
other warranty expressed or implied. IN NO EVENT SHALL SIGNUM SYSTEMS BE LIABLE FOR
CONSEQUENTIAL DAMAGES OF ANY KIND. It is up to the purchaser to determine the reliability and suitability of
this product for his particular application.
1211 FLYNN RD., UNIT #104
C AMARILLO, C A 930 12 , U .S.A
PHONE 805 •
38
3 •
3682
W W W . S I G N U M . C O M
JTAG
PROBES
FOR
SI GNUM
EM ULATORS
T E C H N I C A L
S P E C I F I C A T I O N S
Signum JTAG Probes at a Glance
P A R T
N U M B E R
V O L T A G E
P I N OUT
C P U
D E S C R I P T I O N
P G
ADA-JET-ARM20
ADA-JET-ARM14
ADA-JET-ARM20-LV
ADA-JET-ARM-SWD
3.3 – 5.0V (± 10%)
3.3 – 5.0V (± 10%)
1.8 – 3.3V (± 10%)
0.8 – 5.0V (± 10%)
ARM20
ARM20
ARM14
ARM20
ARM20
Cortex20
Cortex10
Cortex20
Cortex10
TI14
ARM/XScale
Cortex-A/R/M
ARM/XScale
Cortex-A/R/M
ARM/XScale
Cortex-A/R/M
ARM/XScale
Cortex-A/R/M
Cortex-M
Standard 20-pin ARM JTAG probe.
Standard 20-pin ARM JTAG probe with 14-
pin passive extender.
Low voltage version of ADA-JET-ARM20.
Low-voltage probe with Cortex-M SWD and
SWO capabilities.
Conversion adapter from ADA-JET-ARM20
and ADA-JET-ARM20-LV probe to Cortex
20-pin and Cortex 10-pin connectors.
Standard 14-pin JTAG probe for Texas
Instruments DSP and ARM-based
processors.
Low voltage version of ADA-JET-TI14.
JTAG isolation probe for Texas Instruments
DSP and ARM-based processors.
JTAG isolation probe for Texas Instruments
DSP and ARM-based processors with
optional External Power Input.
Low-voltage compact 20-pin JTAG probe for
Texas Instruments DSP and ARM-based
processors.
Conversion ETM to JTAG adapter. Allows
JTAGjet-Trace emulators to be used with
boards without ETM connector.
Conversion adapter to Cortex 20-pin
connector. To be used with JTAGjet-Trace
emulators.
12-pin TI MPSD (legacy) probe.
2
2
3
5
ADA-ARM20-Cortex
N/A (passive)
7
ADA-JET-TI14
3.3 – 5.0V (± 10%)
Texas
Instruments
*
Texas
Instruments
*
Texas
Instruments
**
Texas
Instruments
**
Texas
Instruments
*
Any
8
ADA-JET-TI14-LV
ADA-ISO-TI14
ADA-ISO-TI14-E
1.8 – 3.3V (± 10%)
3.0 – 5.0V (± 10%)
3.3 – 5.0V (± 10%)
TI14
TI14
TI14
8
9
11
ADA-JET-CTI20
1.8 – 3.3V (± 10%)
cTI20
12
ADA-ETM-JTAG
N/A (passive)
ETM38
ARM20
TI14
Cortex20
15
ADA-ETM-SWD20
N/A (passive)
Cortex-M
16
ADA-JET-MPSD
5.0 V (± 10%)
MPSD
TMS320C30/
C31/C32
17
TABLE 1 Comparison of selected Signum JTAG probes.
Any Texas Instruments TMS320 DSP and ARM-based CPU including C2000, C5000, C6000, TMS470, TMS570, OMAP,
DaVinci and Sitara. Consult your CPU/board documentation and for JTAG connector and voltage requirements. Some boards
with Texas Instruments CPUs may also have standard ARM 20-pin connector.
*
**
Isolation probe can be used with any Texas Instruments device, but it is limited to 15MHz JTAG clock.
P I N O U T
P R O B E
P I N O U T
P R O B E
ARM20
ARM14
Cortex20
Cortex10
Figure 2
on page
2
Figure 4
on page
2
Figure 13
on page
5
Figure 14
on page
5
TI14
cTI20
ETM38
MPSD
Figure 18
on page
8
Figure 30
on page
12
Figure 35
on page
14
Figure 44
on page
17
TABLE 2 Signum probe pinouts.
1
SI GNUM
SYSTEM S
JTAG Probes for ARM
ADA-JET-ARM20 and ADA-JET-ARM14
Signum JTAG probes for ARM provide a physical interface between Signum emulators for the ARM processor
and ARM target boards. These probes have 20-pin (ADA-JET-ARM20) and 14-pin (ADA-JET-ARM14)
double-row, polarized, .100" × .100". (2.54 mm × 2.54 mm) female connectors. Signum JTAG probes come
with a 30.5 cm (12 in.) cable. The layout and dimensions of the probes are shown in
Figure 1
through
Figure 10
.
Pin 1
VSupply
GND
GND
GND
GND
GND
GND
GND
GND
18
17
DBGRQ
10
12
14
16
11
13
15
FIGURE 1 The 20-pin JTAG ADA-JET-ARM20 probe
for ARM.
FIGURE 2 The pinout of the ADA-JET-ARM20
probe. Top view.
nSRST
GND
GND
GND
GND
GND
10
12
Pin 1
11
13
1
3
5
7
9
nTRST
VTRef
FIGURE 3 The 14-pin JTAG ADA-JET-ARM14 probe
for ARM.
FIGURE 4
The pinout of the 14-pin JTAG
probe for ARM. Top view.
2
VTRef
TMS
TDO
TCK
TDI
14
2
4
6
8
GND
DBGACK
nSRST
nTRST
VTRef
RTCK
TMS
TDO
TCK
TDI
19
1
3
5
7
9
20
2
4
6
8
NC
JTAG
PROBES
FOR
SI GNUM
EM ULATORS
T E C H N I C A L
S P E C I F I C A T I O N S
L
C
D
Cable to Emulator
Ribbon Cable
FIGURE 5 The dimensions of the ADA-JET-ARM14 probe with a cable extender. L = 63.0 mm (2.5 in.), C =
40.0 mm (1.55 in.) D = 6.0 mm (.24 in.), W = 22.5 mm (.9 in.), H = 11.5 mm (0.45 in.).
A
Cable to Emulator
Cable to Emulator
B
C
D
Pin 1
FIGURE 6 The dimensions of the ADA-JET-
ARM20 probe. Top view. A = 19.3 mm (0.76 in.)
[low-voltage: A = 24.3 mm (0.96 in.)] B = 30.5
mm (1.2 in.)
FIGURE 7 The dimensions of the ADA-JET-ARM20
probe. Side view. C = 22.7 mm (0.88 in.) D = 15.0 mm
(0.59 in.) E = 11.0 mm (0.43 in.)
ADA-JET-ARM20-LV
Your emulator can also be ordered with a low-voltage variant of the JTAG probe (
Figure 8
), or with both
standard and low-voltage variants. These two variants have identical
Caution:
Voltages higher than
pinouts, but slightly differ in dimensions (cf. the caption of
Figure 6
). The
3.3V may permanently damage
voltage range of the low-voltage probe is 1.8V – 3.3V (± 10%).
the low-voltage probe.
Pin 1
VSupply
GND
GND
GND
GND
GND
GND
GND
GND
18
17
DBGRQ
NC
DBGACK
19
20
12
E
H
14
13
TDO
10
11
1
3
5
7
9
nSRST
nTRST
VTRef
RTCK
TMS
TCK
TDI
15
16
2
4
6
8
W
3
