Polymer Chip Capacitors
TOPcap - Basic
Ordering code:
Substitute for:
Date:
B76006D337*M025
B45296R1337M42*
June 2005
© EPCOS AG 2005. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Polymer chip capacitors
TOPcap - Basic
Preliminary Data
Features
Ultra-low ESR
High permissible ripple current
Only 20% derating necessary
Operating temperature 55 … +105
°C
No ignition failure mode
Lead-free and material content in
compliance with RoHS and SGS
Suitable for lead-free soldering
Taped and reeled to IEC 60286-3
Technical data and ordering code
Ordering code
Rated capacitance
Rated voltage
Capacitance tolerance
Operating temperature range
Maximum leakage current
Maximum dissipation factor
Maximum equivalent series
resistance
Maximum ripple current
(20
°C,
120 Hz)
(20
°C,
100 kHz)
(tinned terminals)
(20
°C,
120 Hz)
(up to 85
°C)
(up to 105
°C)
C
R
V
R
∆C
R
T
op
(20
°C,
V
R
, 5 min) I
leak,max
DF
max
B76006D337*M025
B76006D337*M025
330
6.3
5.0
±20
55 ... +105
208
10
µF
VDC
%
°C
µA
%
mΩ
A
ESR
max
25
2.5
2.2
1.0
D
7343-31
(20
°C,
100 kHz) I
AC,max
(85
°C,
100 kHz)
(105
°C,
100 kHz)
Case size
EIA/IECQ
Dimensions
(L x W x H)
Failure rate
(1 fit = 1 10
-9
failures/h)
Service life
Moisture level
*=
(at 40
°C; ≤
V
R
,
R
S
≤
0.1
Ω/V)
7.3
±0.3
x 4.3
±0.3
x 2.8
±0.3
mm
(0.287
±0.012
x 0.169
±0.012
(inch)
x 0.110
±0.012)
≤264
fit
>500000
MSL 3
h
Code number for reel diameter
6 = 330-mm reel
9 = 180-mm reel
Please read
Important notes
at the end of this document
Page 2 of 6
Polymer chip capacitors
TOPcap - Basic
Preliminary Data
Ordering code structure
B76
TOPcap family
B76006D337*M025
0
02
D
337
9
M
025
Series
0 = Basic
1 = 125
°C
3 = Multiple Anode
Rated voltage
02 = 2.5 V, 04 = 4 V, 06 = 6.3 V, 10 = 10 V,
16 = 16 V, 20 = 20 V, 25 = 25 V
Case size
B, C, D, E, F, R, V, X
Rated capacitance + exponent
C [pF] 10
x
686 = 68 pF 10
6
= 68
µF,
157 = 15 pF
10
7
= 150
µF,
108 = 10 pF
10
8
= 1000
µF
Reel diameter
9 = 180 mm, 6 = 330 mm
Capacitance tolerance
M =
±20%
ESR value
E.g.: 009 = 9 mΩ, 018 = 18 mΩ, 045 = 45 mΩ
Please read
Important notes
at the end of this document
Page 3 of 6
Polymer chip capacitors
TOPcap - Basic
Preliminary Data
B76006D337*M025
Infrared reflow soldering, hot air reflow soldering (lead-free solders alloys)
Temperature curve at component terminal in infrared and hot air soldering
Other profiles and peak temperatures upon request.
Storage conditions
EPCOS polymer capacitors are shipped in moisture barrier bags together with a desiccant and a
moisture indicator card.
All series (B760, B761, B763) are classified according JEDEC J-STD-020C as MSL 3 (Moisture
Sensitivity Level 3). Parts should be mounted 168 hours (= 7 days) after opening the moisture
barrier bags to prevent absorption of moisture and outgassing effects during soldering. Following
rules should be adhered to:
Parts must be stored in the reel and sealed moisture barrier bag until usage.
Parts should not be stored at high temperature, high humidity, corrosive atmospheres and
exposed to direct sun light. To enable the floor life of 168 hours according JEDEC a maximum
temperature of 30°C at a humidity of maximum 60% R.H. is required.
Temperature fluctuation should be minimized.
Please read
Important notes
at the end of this document
Page 4 of 6
Polymer chip capacitors
TOPcap - Basic
Preliminary Data
Derating recommendations
B76006D337*M025
Max. permissible continuous voltage (operating
voltage) versus temperature
Environmental comments and warnings
As a manufacturer of passive components, we develop our products on the basis of the relevant
standards and laws, and thus ensure that our products are free of those materials and
substances prohibited by the relevant legislation.
To ensure a standardized procedure for EPCOS worldwide, a binding list of materials and
substances is included in our environment management system to ISO 14001. Our planning and
development guidelines include regulations and directives aiming to promote recognition of
environmental aspects and to optimize products and processes in terms of material use and
environmental compatibility, to design them with a sparing use of resources and to replace
hazardous substances as far as possible.
The environmental officer provides support in assessing the environmental risks of a
development project upon request. Consideration of environmental aspects is checked and
recorded at the design reviews.
EPCOS polymer chip capacitors are RoHS compliant.
Please read
Important notes
at the end of this document
Page 5 of 6
FPGA/CPLD
