New Product Release
Surface Mount Ceramic Chip Capacitors
Extended Values 0603, X7R Dielectric, 100 & 200 Volts
100 Volts – 12,000 pF - 39,000 pF
200 Volts – 1,200 pF - 10,000 pF
Outline Drawings
Table 1 - Dimensions - Millimeters
EIA
Metric Size
Size Code Code (Ref)
0603*
1608
L#
Length
1.6 (.063) ± 0.15 (.006)
W#
Width
0.8 (.032) ± 0.15 (.006)
Thickness
See Table 2
B
Bandwidth
0.35 (.014) ± 0.15 (.006)
S
Min. Separation
0.7 (.028)
Mounting
Technique
Solder Wave or
Solder Reflow
Table 2 - Ratings & Part Number Listing
Cap Values
12,000pF
15,000pF
18,000pF
22,000pF
27,000pF
33,000pF
39,000pF
1,200pF
1,500pF
1,800pF
2,200pF
2,700pF
3,300pF
3,900pF
4,700pF
5,600pF
6,800pF
8,200pF
10,000pF
KEMET Part Number
C0603C123(1)1RAC
C0603C153(1)1RAC
C0603C183(1)1RAC
C0603C223(1)1RAC
C0603C273(1)1RAC
C0603C333(1)1RAC
C0603C393(1)1RAC
C0603C122(1)2RAC
C0603C152(1)2RAC
C0603C182(1)2RAC
C0603C222(1)2RAC
C0603C272(1)2RAC
C0603C332(1)2RAC
C0603C392(1)2RAC
C0603C472(1)2RAC
C0603C562(1)2RAC
C0603C682(1)2RAC
C0603C822(1)2RAC
C0603C103(1)2RAC
Capacitance Tolerance
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
J,K,M
Thickness - mm
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
0.8 ± 0.1
Qty 7” Reel
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
Qty 13” Reel
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
To complete the KEMET part number, insert capacitance tolerance: J - ±5%, K - ±10% or M ±20%.
F3272 02/05
Electrical Parameters
As detailed in the KEMET Surface Mount Catalog F3102 for X7R, with following specific requirements based on
room temperature (25°C) parameters:
• Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to ± 15% over that range
• Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 1000
megohm microfarads or 100 gigohms, whichever is less.
• Capacitance and Dissipation Factor (DF) measured at 1KHz at 1.0Vrms.
25 Volts - DF Limit is 3.5%
>25
Volts - DF Limit is 2.5%
.
Soldering Process
Wave soldering or reflow soldering is acceptable for these chips.
Marking
These chips are normally supplied unmarked. If required, they can be laser marked as an extra cost option.
More detail on the marking format is included in our Surface Mount Catalog F3102.
In general, the information in the KEMET Surface Mount catalog F3102 applies to these capacitors. The information in
this bulletin supplements that in the catalog.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • (864) 963-6300 • www.kemet.com
