型号
  • 型号
  • 关键词
首页 > 器件类别 > 电源/电源管理 > 电源电路

CAT1025ZD4I-42-T3

1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, 3 X 3 MM, 0.80 MM HEIGHT, HALOGEN FREE AND ROHS COMPLIANT, MO-229, TDFN-8

器件类别：电源/电源管理    电源电路   

厂商名称：ON Semiconductor(安森美)

厂商官网：http://www.onsemi.cn

下载文档
参数 预览 参数对比
器件参数
参数名称
属性值
厂商名称
ON Semiconductor(安森美)
零件包装代码
SON
包装说明
HVSON,
针数
8
Reach Compliance Code
unknow
其他特性
RESET THRESHOLD VOLTAGE IS 4.375V; MANUAL RESET INPUT
可调阈值
NO
模拟集成电路 - 其他类型
POWER SUPPLY SUPPORT CIRCUIT
JESD-30 代码
S-PDSO-N8
JESD-609代码
e3
长度
3 mm
信道数量
1
功能数量
1
端子数量
8
最高工作温度
85 °C
最低工作温度
-40 °C
封装主体材料
PLASTIC/EPOXY
封装代码
HVSON
封装形状
SQUARE
封装形式
SMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE
认证状态
Not Qualified
座面最大高度
0.8 mm
最大供电电压 (Vsup)
5.5 V
最小供电电压 (Vsup)
2.7 V
标称供电电压 (Vsup)
5 V
表面贴装
YES
技术
CMOS
温度等级
INDUSTRIAL
端子面层
MATTE TIN
端子形式
NO LEAD
端子节距
0.65 mm
端子位置
DUAL
宽度
3 mm
文档预览
CAT1024, CAT1025
Supervisory Circuits with I C Serial 2k-bit
CMOS EEPROM and Manual Reset
FEATURES
Precision Power Supply Voltage Monitor
— 5 V, 3.3 V and 3 V systems
— Five threshold voltage options
Active High or Low Reset
— Valid reset guaranteed at V
CC
= 1 V
400 kHz I
2
C Bus
2.7 V to 5.5 V Operation
Low power CMOS technology
16-Byte Page Write Buffer
Built-in inadvertent write protection
— WP pin (CAT1025)
1,000,000 Program/Erase cycles
Manual Reset Input
100 year data retention
Industrial and extended temperature ranges
Green packages available with NiPdAu Lead
finished
2
DESCRIPTION
The CAT1024 and CAT1025 are complete memory
and supervisory solutions for microcontroller-based
systems. A 2k-bit serial EEPROM memory and a
system power supervisor with brown-out protection
are integrated together in low power CMOS techno–
logy. Memory interface is via a 400 kHz I
2
C bus.
The CAT1025 provides a precision V
CC
sense circuit
and two open drain outputs: one (RESET) drives high
¯¯¯¯¯¯
and the other (RESET) drives low whenever V
CC
falls
below the reset threshold voltage. The CAT1025 also
has a Write Protect input (WP). Write operations are
disabled if WP is connected to a logic high.
The CAT1024 also provides a precision V
CC
sense
¯¯¯¯¯¯
circuit, but has only a RESET output and does not
have a Write Protect input.
The power supply monitor and reset circuit protect
memory and system controllers during power up/down
and against brownout conditions. Five reset threshold
voltages support 5 V, 3.3 V and 3 V systems. If power
supply voltages are out of tolerance reset signals
become active, preventing the system microcontroller,
ASIC or peripherals from operating. Reset signals
become inactive typically 200 ms after the supply
voltage exceeds the reset threshold level. With both
active high and low reset signals, interface to
microcontrollers and other ICs is simple. In addition,
¯¯¯¯¯¯
the RESET pin or a separate input, ¯¯¯, can be used
MR
as an input for push-button manual reset capability.
The CAT1024/25 memory features a 16-byte page. In
addition, hardware data protection is provided by a
V
CC
sense circuit that prevents writes to memory
whenever V
CC
falls below the reset threshold or until
V
CC
reaches the reset threshold during power up.
Available packages include an 8-pin PDIP and a
surface mount 8-pin SO, 8-pin TSSOP, 8-pin TDFN
and 8-pin MSOP packages. The TDFN package thick-
ness is 0.8 mm maximum. TDFN footprint is 3 x 3 mm.
For Ordering Information details, see page 19.
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
1
Doc. No. MD-3008 Rev. R
CAT1024, CAT1025
BLOCK DIAGRAM
EXTERNA LOAD
L
DOUT
ACK
VCC
VSS
WORDADDRESS
BUFFERS
START/STOP
LOGIC
2kbit
EEPROM
COLUMN
DECODERS
SENSEAMPS
SHIFT REGISTERS
THRESHOLD VOLTAGE OPTION
Part Dash
Number
-45
-42
-30
-28
-25
Minimum
Threshold
4.50
4.25
3.00
2.85
2.55
Maximum
Threshold
4.75
4.50
3.15
3.00
2.70
SDA
XDEC
WP*
CONTR
OL
LOGIC
DATA IN STORAGE
HIGHVOLTAGE/
TIMING CONTR
OL
RESET Controller
MR
Precision
Vcc Monitor
STATE COUNTERS
SLAVE
ADDRESS
COMPARATORS
SCL
RESET*
* CAT1025 Only
RESET
PIN CONFIGURATION
DIP Package (L)
SOIC Package (W)
TSSOP Package (Y)
MSOP Package (Z)
¯¯¯
MR
¯¯¯¯¯¯
RESET
NC
V
SS
¯¯¯
MR
¯¯¯¯¯¯
RESET
RESET
V
SS
1
2
3
4
CAT1024
8
7
6
5
V
CC
NC
SCL
SDA
(Bottom View)
TDFN Package: 3 mm x 3 mm
0.8mm maximum height - (ZD4)
V
CC
8
NC 7
CAT1024
SCL 6
SDA 5
V
CC
8
WDI 7
CAT1025
SCL 6
SDA 5
1
¯¯¯
MR
¯¯¯¯¯¯
2
RESET
3 NC
4 V
SS
1
¯¯¯
MR
¯¯¯¯¯¯
2
RESET
3 RESET
4 V
SS
1
2
3
4
CAT1025
8
7
6
5
V
CC
WP
SCL
SDA
Doc. No. MD-3008 Rev. R
2
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
CAT1024, CAT1025
PIN DESCRIPTION
¯¯¯¯¯¯
RESET/RESET:
RESET OUTPUTs
(RESET CAT1025 Only)
¯¯¯¯¯¯
These are open drain pins and RESET can be used
as a manual reset trigger input. By forcing a reset
condition on the pin the device will initiate and
maintain a reset condition. The RESET pin must be
connected through a pull-down resistor, and the
¯¯¯¯¯¯
RESET pin must be connected through a pull-up
resistor.
SDA:
SERIAL DATA ADDRESS
The bidirectional serial data/address pin is used to
transfer all data into and out of the device. The SDA
pin is an open drain output and can be wire-ORed
with other open drain or open collector outputs.
SCL:
SERIAL CLOCK
Serial clock input.
¯¯¯:
MANUAL RESET INPUT
MR
Manual Reset input is a debounced input that can be
connected to an external source for Manual Reset.
Pulling the MR input low will generate a Reset
condition. Reset outputs are active while ¯¯¯ input is
MR
low and for the reset timeout period after ¯¯¯ returns
MR
to high. The input has an internal pull up resistor.
WP (CAT1025 Only):
WRITE PROTECT INPUT
When WP input is tied to V
SS
or left unconnected write
operations to the entire array are allowed. When tied
to V
CC
, the entire array is protected. This input has an
internal pull down resistor.
PIN FUNCTION
Pin
Name
NC
¯¯¯¯¯¯
RESET
V
SS
SDA
SCL
RESET
V
CC
WP
¯¯¯
MR
Function
No Connect
Active Low Reset Input/Output
Ground
Serial Data/Address
Clock Input
Active High Reset Output
(CAT1025 only)
Power Supply
Write Protect (CAT1025 only)
Manual Reset Input
OPERATING TEMPERATURE RANGE
Industrial
Extended
-40ºC to 85ºC
-40ºC to 125ºC
CAT10XX FAMILY OVERVIEW
Device
CAT1021
CAT1022
CAT1023
CAT1024
CAT1025
CAT1026
CAT1027
WDI
Manual
Reset
Input Pin
Watchdog
Watchdog
Monitor
Pin
SDA
SDA
WDI
Write
Protection
Pin
Independent
Auxiliary
Voltage Sense
RESET:
Active High
and LOW
EEPROM
2k
2k
2k
2k
2k
2k
2k
For supervisory circuits with embedded 16k EEPROM, please refer to the CAT1161, CAT1162 and CAT1163
data sheets.
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
3
Doc. No. MD-3008 Rev. R
CAT1024, CAT1025
ABSOLUTE MAXIMUM RATINGS
(1)
Parameters
Temperature Under Bias
Storage Temperature
Voltage on any Pin with Respect to Ground
(2)
V
CC
with Respect to Ground
Package Power Dissipation Capability (T
A
= 25°C)
Lead Soldering Temperature (10 s)
Output Short Circuit Current
(3)
Ratings
–55 to +125
–65 to +150
–2.0 to V
CC
+ 2.0
–2.0 to 7.0
1.0
300
100
Units
ºC
ºC
V
V
W
ºC
mA
D.C. OPERATING CHARACTERISTICS
V
CC
= 2.7 V to 5.5 V and over the recommended temperature conditions unless otherwise specified.
Symbol
I
LI
I
LO
I
CC1
I
CC2
I
SB
V
IL(4)
V
IH(4)
V
OL
V
OH
Parameter
Input Leakage Current
Output Leakage Current
Power Supply Current (Write)
Power Supply Current (Read)
Standby Current
Input Low Voltage
Input High Voltage
Output Low Voltage
¯¯¯¯¯¯
(SDA, RESET)
Output High Voltage
(RESET)
I
OL
= 3 mA
V
CC
= 2.7 V
I
OH
= -0.4 mA
V
CC
= 2.7V
CAT102x-45
(V
CC
= 5.0 V)
CAT102x-42
(V
CC
= 5.0 V)
V
TH
Reset Threshold
CAT102x-30
(V
CC
= 3.3 V)
CAT102x-28
(V
CC
= 3.3 V)
CAT102x-25
(V
CC
= 3.0 V)
V
RVALID
V
RT
(5)
Test Conditions
V
IN
= GND to V
CC
V
IN
= GND to V
CC
f
SCL
= 400 kHz
V
CC
= 5.5 V
f
SCL
= 400 kHz
V
CC
= 5.5 V
Vcc = 5.5 V,
V
IN
= GND or V
CC
Min
-2
-10
Typ
Max
10
10
3
1
40
Units
µA
µA
mA
mA
µA
V
V
V
V
-0.5
0.7 x Vcc
0.3 x V
CC
V
CC
+ 0.5
0.4
V
CC
- 0.75
4.50
4.25
3.00
2.85
2.55
1.00
15
4.75
4.50
3.15
3.00
2.70
V
Reset Output Valid V
CC
Voltage
Reset Threshold Hysteresis
V
mV
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
(2) The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC
voltage on output pins is V
CC
+0.5 V, which may overshoot to V
CC
+2.0 V for periods of less than 20 ns.
(3) Output shorted for no more than one second. No more than one output shorted at a time.
(4) V
IL
min and V
IH
max are reference values only and are not tested.
(5) This parameter is tested initially and after a design or process change that affects the parameter. Not 100% tested.
Doc. No. MD-3008 Rev. R
4
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
CAT1024, CAT1025
CAPACITANCE
T
A
= 25ºC, f = 1.0 MHz, V
CC
= 5 V
Symbol
C
OUT (1)
C
IN(1)
Test
Output Capacitance
Input Capacitance
Test Conditions
V
OUT
= 0 V
V
IN
= 0 V
Max
8
6
Units
pF
pF
AC CHARACTERISTICS
V
CC
= 2.7 V to 5.5 V and over the recommended temperature conditions, unless otherwise specified.
Memory Read & Write Cycle
(2)
Symbol
f
SCL
t
SP
t
LOW
t
HIGH
t
R(1)
t
F
(1)
Parameter
Clock Frequency
Input Filter Spike Suppression (SDA, SCL)
Clock Low Period
Clock High Period
SDA and SCL Rise Time
SDA and SCL Fall Time
Start Condition Hold Time
Start Condition Setup Time (for a Repeated Start)
Data Input Hold Time
Data Input Setup Time
Stop Condition Setup Time
SCL Low to Data Out Valid
Data Out Hold Time
Time the Bus must be Free Before a New Transmission Can Start
Write Cycle Time (Byte or Page)
Min
Max
400
100
Units
kHz
ns
µs
µs
1.3
0.6
300
300
0.6
0.6
0
100
0.6
900
50
1.3
5
ns
ns
µs
µs
ns
ns
µs
ns
ns
µs
ms
t
HD; STA
t
SU; STA
t
HD; DAT
t
SU; DAT
t
SU; STO
t
AA
t
DH
t
BUF
(1)
t
WC(3)
Notes:
(1) This parameter is characterized initially and after a design or process change that affects the parameter. Not 100% tested.
(2) Test Conditions according to “AC Test Conditions” table.
(3) The write cycle time is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the
write cycle, the bus interface circuits are disabled, SDA is allowed to remain high and the device does not respond to its slave address.
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
5
Doc. No. MD-3008 Rev. R
查看更多>
参数对比
与CAT1025ZD4I-42-T3相近的元器件有：CAT1025YI-45-G、CAT1025ZD4I-25-T3、CAT1025YI-28-G、CAT1025YI-30-G、CAT1025YI-42-G、CAT1025YI-25-G、CAT1025ZD4I-28-T3、CAT1025ZD4I-45-T3、CAT1025ZD4I-30-T3。描述及对比如下：
型号 CAT1025ZD4I-42-T3 CAT1025YI-45-G CAT1025ZD4I-25-T3 CAT1025YI-28-G CAT1025YI-30-G CAT1025YI-42-G CAT1025YI-25-G CAT1025ZD4I-28-T3 CAT1025ZD4I-45-T3 CAT1025ZD4I-30-T3
描述 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, 3 X 3 MM, 0.80 MM HEIGHT, HALOGEN FREE AND ROHS COMPLIANT, MO-229, TDFN-8 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, ROHS COMPLIANT, MO-153, TSSOP-8 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, 3 X 3 MM, 0.80 MM HEIGHT, HALOGEN FREE AND ROHS COMPLIANT, MO-229, TDFN-8 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, ROHS COMPLIANT, MO-153, TSSOP-8 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, ROHS COMPLIANT, MO-153, TSSOP-8 IC 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, ROHS COMPLIANT, MO-153, TSSOP-8, Power Management Circuit IC 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, ROHS COMPLIANT, MO-153, TSSOP-8, Power Management Circuit 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, 3 X 3 MM, 0.80 MM HEIGHT, HALOGEN FREE AND ROHS COMPLIANT, MO-229, TDFN-8 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, 3 X 3 MM, 0.80 MM HEIGHT, HALOGEN FREE AND ROHS COMPLIANT, MO-229, TDFN-8 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, 3 X 3 MM, 0.80 MM HEIGHT, HALOGEN FREE AND ROHS COMPLIANT, MO-229, TDFN-8
厂商名称 ON Semiconductor(安森美) ON Semiconductor(安森美) ON Semiconductor(安森美) ON Semiconductor(安森美) ON Semiconductor(安森美) ON Semiconductor(安森美) ON Semiconductor(安森美) ON Semiconductor(安森美) ON Semiconductor(安森美) ON Semiconductor(安森美)
零件包装代码 SON TSSOP SON TSSOP TSSOP TSSOP TSSOP SON SON SON
包装说明 HVSON, TSSOP, HVSON, TSSOP, TSSOP, TSSOP, TSSOP, HVSON, HVSON, HVSON,
针数 8 8 8 8 8 8 8 8 8 8
Reach Compliance Code unknow compliant unknown compliant compliant compliant compliant unknown unknown unknown
其他特性 RESET THRESHOLD VOLTAGE IS 4.375V; MANUAL RESET INPUT RESET THRESHOLD VOLTAGE IS 4.375V; MANUAL RESET INPUT RESET THRESHOLD VOLTAGE IS 2.625V; MANUAL RESET INPUT RESET THRESHOLD VOLTAGE IS 2.925V; MANUAL RESET INPUT RESET THRESHOLD VOLTAGE IS 3.075V; MANUAL RESET INPUT RESET THRESHOLD VOLTAGE IS 4.375V; MANUAL RESET INPUT RESET THRESHOLD VOLTAGE IS 2.625V; MANUAL RESET INPUT RESET THRESHOLD VOLTAGE IS 2.925V; MANUAL RESET INPUT RESET THRESHOLD VOLTAGE IS 4.625V; MANUAL RESET INPUT RESET THRESHOLD VOLTAGE IS 3.075V; MANUAL RESET INPUT
可调阈值 NO NO NO NO NO NO NO NO NO NO
模拟集成电路 - 其他类型 POWER SUPPLY SUPPORT CIRCUIT POWER SUPPLY SUPPORT CIRCUIT POWER SUPPLY SUPPORT CIRCUIT POWER SUPPLY SUPPORT CIRCUIT POWER SUPPLY SUPPORT CIRCUIT POWER SUPPLY SUPPORT CIRCUIT POWER SUPPLY SUPPORT CIRCUIT POWER SUPPLY SUPPORT CIRCUIT POWER SUPPLY SUPPORT CIRCUIT POWER SUPPLY SUPPORT CIRCUIT
JESD-30 代码 S-PDSO-N8 R-PDSO-G8 S-PDSO-N8 R-PDSO-G8 R-PDSO-G8 R-PDSO-G8 R-PDSO-G8 S-PDSO-N8 S-PDSO-N8 S-PDSO-N8
JESD-609代码 e3 e4 e3 e4 e4 e4 e4 e3 e3 e3
长度 3 mm 4.4 mm 3 mm 4.4 mm 4.4 mm 4.4 mm 4.4 mm 3 mm 3 mm 3 mm
信道数量 1 1 1 1 1 1 1 1 1 1
功能数量 1 1 1 1 1 1 1 1 1 1
端子数量 8 8 8 8 8 8 8 8 8 8
最高工作温度 85 °C 85 °C 85 °C 85 °C 85 °C 85 °C 85 °C 85 °C 85 °C 85 °C
最低工作温度 -40 °C -40 °C -40 °C -40 °C -40 °C -40 °C -40 °C -40 °C -40 °C -40 °C
封装主体材料 PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY
封装代码 HVSON TSSOP HVSON TSSOP TSSOP TSSOP TSSOP HVSON HVSON HVSON
封装形状 SQUARE RECTANGULAR SQUARE RECTANGULAR RECTANGULAR RECTANGULAR RECTANGULAR SQUARE SQUARE SQUARE
封装形式 SMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE SMALL OUTLINE, THIN PROFILE, SHRINK PITCH SMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE SMALL OUTLINE, THIN PROFILE, SHRINK PITCH SMALL OUTLINE, THIN PROFILE, SHRINK PITCH SMALL OUTLINE, THIN PROFILE, SHRINK PITCH SMALL OUTLINE, THIN PROFILE, SHRINK PITCH SMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE SMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE SMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE
认证状态 Not Qualified Not Qualified Not Qualified Not Qualified Not Qualified Not Qualified Not Qualified Not Qualified Not Qualified Not Qualified
座面最大高度 0.8 mm 1.2 mm 0.8 mm 1.2 mm 1.2 mm 1.2 mm 1.2 mm 0.8 mm 0.8 mm 0.8 mm
最大供电电压 (Vsup) 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V
最小供电电压 (Vsup) 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V
标称供电电压 (Vsup) 5 V 5 V 3 V 3.3 V 3.3 V 5 V 3 V 3.3 V 5 V 3.3 V
表面贴装 YES YES YES YES YES YES YES YES YES YES
技术 CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS
温度等级 INDUSTRIAL INDUSTRIAL INDUSTRIAL INDUSTRIAL INDUSTRIAL INDUSTRIAL INDUSTRIAL INDUSTRIAL INDUSTRIAL INDUSTRIAL
端子面层 MATTE TIN Nickel/Palladium/Gold (Ni/Pd/Au) MATTE TIN Nickel/Palladium/Gold (Ni/Pd/Au) Nickel/Palladium/Gold (Ni/Pd/Au) Nickel/Palladium/Gold (Ni/Pd/Au) NICKEL PALLADIUM GOLD MATTE TIN MATTE TIN MATTE TIN
端子形式 NO LEAD GULL WING NO LEAD GULL WING GULL WING GULL WING GULL WING NO LEAD NO LEAD NO LEAD
端子节距 0.65 mm 0.65 mm 0.65 mm 0.65 mm 0.65 mm 0.65 mm 0.65 mm 0.65 mm 0.65 mm 0.65 mm
端子位置 DUAL DUAL DUAL DUAL DUAL DUAL DUAL DUAL DUAL DUAL
宽度 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm
Base Number Matches - 1 1 1 1 1 1 1 - -
热门器件
热门资源推荐
独立光伏电源系统设计方法 基于Windows CENET的串行通信的实现.pdf 超级电容器的储能特性和应用 A new three-level soft-switched converter 10KV配电线路上装设分段断路器的方法 [资料]-JIS B8631-2-2011 冷凍冷蔵ショーケース－第２部：分類，構造，特性及び試験条件.pdf 更多资料分享地址.txt -CE认证测试项目详细及需提供材料.pdf 台湾远翔科技充电IC系列之FP6116规格书 MP3MP4电源电路原理及维修方法.pdf
“恒流”和“恒压”原理 工程师必懂：pcb layout 前必须考虑的“5种”生产工艺！ 脉冲激励电路求助 变频器、逆变器电路 你也会这样设计脉冲负载的电源吗？有问题的网友进鸭~ 求大神帮忙 [EETalk]钠电新势力，新老玩家纷纷入局竞争激烈，对此，你怎么看？ 一种带辅助变压器的Flyback变换器ZVS软开关实现方案 焊接逆变电源的发展趋势浅谈 SiC与ZVS软开关电路更配！——谈怎么提高ZVS电路效率
PIC单片机控制的遥控防盗报警器电路 用数字电路CD4069制作的万能遥控轻触开关 红外线探测报警器 短波AM发射器电路设计图 使用ESP8266从NTP服务器获取时间并在OLED显示器上显示 开关电源的基本组成及工作原理 用NE555制作定时器 带有短路保护系统的5V直流稳压电源电路图 如何调制IC555振荡器 基于ICL296的大电流开关稳压器电源电路
器件捷径:
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ
需要登录后才可以下载。
登录取消