The EL1510C is a dual operational amplifier designed for central
office and customer premise line driving in both SDSL and ADSL
solutions. This device features a high drive capability of 250mA while
consuming only 7.5mA of supply current per amplifier, operating
from ±12V supplies. This driver achieves a typical distortion of less
than -85dBc, at 150kHz into a 25Ω load. The EL1510CL is available
in the power 8-pin LPP package and is specified for operation over the
full -40°C to +85°C temperature range. The LPP package has the
potential for a very low junction to ambient thermal resistance of
43°C/W, making it suitable for high power applications. The
EL1510CS is in the 8-pin SO package and thus is limited to applica-
tions where the power dissipation in the device is less than 781mW.
The EL1510C is ideal for CPE modem applications in ADSL, HDSL2,
G.SHDSL, and VDSL.
Applications
•
•
•
•
•
ADSL G.lite CO line driving
G.SHDSL, HDSL2 line drivers
ADSL full rate CPE line driving
Video distribution amplifiers
Video twisted-pair line drivers
Ordering Information
Part No
EL1510CS
EL1510CS-T7
EL1510CS-T13
EL1510CL
EL1510CL-T7
EL1510CL-T13
Package
8-Pin SO
8-Pin SO
8-Pin SO
8-Pin LPP
8-Pin LPP
8-Pin LPP
Tape & Reel
-
7”
13”
-
7”
13”
Outline #
MDP0027
MDP0027
MDP0027
MDP0047
MDP0047
MDP0047
Connection Diagrams
OUTA 1
INA- 2
INA+ 3
GND
4
-
+
8-Pin SO
-
+
8 VS
7 OUTB
6 INB-
5 INB+
OUTA
INA-
INA+
GND
1
2
3
4
8
7
6
5
VS
OUTB
INB-
INB+
September 18, 2001
-
+
Amp A
-
+
Amp B
8-Pin LPP Top View
Note:
All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir-
cuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described
herein and makes no representations that they are free from patent infringement.
WARNING - Life Support Policy
September 18, 2001
Elantec Semiconductor, Inc.
675 Trade Zone Blvd.
Milpitas, CA 95035
Telephone: (408) 945-1323
(888) ELANTEC
Fax:
(408) 945-9305
European Office: +44-118-977-6020
Japan Technical Center: +81-45-682-5820
2
Elantec, Inc. products are not authorized for and should not be used
within Life Support Systems without the specific written consent of
Elantec, Inc. Life Support systems are equipment intended to sup-
port or sustain life and whose failure to perform when properly used
in accordance with instructions provided can be reasonably
expected to result in significant personal injury or death. Users con-
templating application of Elantec, Inc. Products in Life Support
Systems are requested to contact Elantec, Inc. factory headquarters
to establish suitable terms & conditions for these applications. Elan-
tec, Inc.’s warranty is limited to replacement of defective
components and does not cover injury to persons or property or
