FPR 2-T218
Powertron
•
•
•
•
•
•
Resistances from 0.002Ohm to 50Ohms
Power Rating to 30Watt
Resistance Tolerances to ±0.25%
TCR to ±15ppm/K
Load Stability to 0.1%
TO-218 (TO-247) Housing
SPECIFICATIONS
Type
Resistance Range
Power rating
free air 70°C
with heatsink
Thermal Resistance Rthj-c
Tolerances
from 0.002 Ohms
from 0.01 Ohms
from 0.02 Ohms
Stability
Temperature Coefficient
Voltage Proof
Thermal EMF
Operating Temperature Range
Resistor Material
Substrate
Housing
Connector Material
Terminals
Max. Torque
1% / 2% / 5%
0.5% / 1% / 2% / 5%
0.25% / 0.5% / 1% / 2% / 5%
0.1% / 0.2% / 0.5%
(depends on stress)
R > 0.2 Ohms ±15ppm/K (20 to 60°C)
R ≤ 0.2 Ohms TCR see table A next page
300 VDC
< 0.1µV/K
-40 to 130°C
CuNiMn-Foil
anodized aluminium
PPS
Cu tinned
2
1 Nm
FPR 2-T218
0.002 to 50 Ohms
2W
30 W
2.5 K/W
Derating
Power Rating Notes -
The FPR Series Resistors must be attached to a suitable heat-
sink. The maximum internal resistor temperature is 130°C.
To specify an appropriate heatsink use the following formula :
R
qH
= T
MAX
- ( P x R
qR
) - T
A
P
Where:
R
qH
= Thermal Resistance of Heatsink ( K/W )
R
qR
= Thermal Resistance of Resistor ( K/W )
T
MAX
= Maximum Temperature of Resistor
T
A
= Ambient Temperature of Heatsink ( °C )
P = Power Through Resistor ( W )
Ordering Information
Part Number - Resistance - Contact - Tolerance
FPR 2-T218 0.068 Ohms A 0.5%
Document Number: 64200
Revision: 20-09-10
For technical questions, contact:
powertron@vishaypg.com
www.powertron.de
1
FPR 2-T218
Powertron
SPECIFICATIONS
(continued)
Temperature Coefficient
4000
250
table A
2000
DR/R
(ppm)
+15ppm/K
200
0
TCR-Shift (ppm/K)
150
-2000
-15ppm/K
100
-4000
Limit 2 (3s)
-6000
Nominal
DR/R
Limit 1 (3s)
50
0
10
20
50
2
5
100
200
-8000
-40
-20
0
20
40
60
Temperature (°C)
80
100
120
140
Resistance Value (mOhm)
Dimensions
Dimension
A
B
C
D
E
F
G
H (A-Contact)
H (B-Contact)
H (C-Contact)
I
J
K
L (A-Contact)
L (B-Contact)
L (C-Contact)
M (A-Contact)
M (B-Contact)
M (C-Contact)
N
O
P
Q
R
mm
21.10
15.50
4.90
4.00
12.60
Ø3.2
2.95
17.65
16.85
17.75
10.16
1.40
3.00
7.70
5.00
14.50
2.70
1.90
2.80
1.65
4.60
6.15
0.80
2.00
tol.
(±mm)
0.2
0.2
0.1
0.1
0.2
0.1
0.1
0.2
0.2
0.2
0.2
0.1
0.1
0.2
0.2
0.2
0.1
0.1
0.1
0.1
0.1
0.2
0.1
0.1
inches
0.83
0.61
0.19
0.16
0.50
Ø0.13
0.12
0.69
0.66
0.70
0.40
0.06
0.12
0.30
0.20
0.57
0.11
0.07
0.11
0.06
0.18
0.24
0.03
0.08
tol.
(±inches)
0.008
0.008
0.004
0.004
0.008
0.004
0.004
0.008
0.008
0.008
0.008
0.004
0.004
0.008
0.008
0.008
0.004
0.004
0.004
0.004
0.004
0.008
0.004
0.004
www.powertron.de
2
For technical questions, contact:
powertron@vishaypg.com
Document Number: 64200
Revision: 20-09-10
Legal Disclaimer Notice
Vishay Precision Group
Disclaimer
ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their
behalf (collectively, “Vishay Precision Group”), disclaim any and all liability for any errors, inaccuracies or
incompleteness contained herein or in any other disclosure relating to any product.
The product specifications do not expand or otherwise modify Vishay Precision Group’s terms and conditions of
purchase, including but not limited to, the warranty expressed therein.
Vishay Precision Group makes no warranty, representation or guarantee other than as set forth in the terms
and conditions of purchase.
To the maximum extent permitted by applicable law, Vishay Precision Group
disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability,
including without limitation special, consequential or incidental damages, and (iii) any and all implied
warranties, including warranties of fitness for particular purpose, non-infringement and merchantability.
Information provided in datasheets and/or specifications may vary from actual results in different applications
and performance may vary over time. Statements regarding the suitability of products for certain types of
applications are based on Vishay Precision Group’s knowledge of typical requirements that are often placed on
Vishay Precision Group products. It is the customer’s responsibility to validate that a particular product with the
properties described in the product specification is suitable for use in a particular application.
No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by
any conduct of Vishay Precision Group.
The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise
expressly indicated. Customers using or selling Vishay Precision Group products not expressly indicated for use
in such applications do so entirely at their own risk and agree to fully indemnify Vishay Precision Group for any
damages arising or resulting from such use or sale. Please contact authorized Vishay Precision Group personnel
to obtain written terms and conditions regarding products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document No.: 63999
Revision: 27-Apr-11
www.vishaypg.com
1
RF/无线
