FSP-63.25JE-20,FSP-63.25JE-20 pdf中文资料,FSP-63.25JE-20引脚图,FSP-63.25JE-20电路-Datasheet-电子工程世界

文档预览

Flexible Interconnections

Flexstrip

ESCRIPTION

PPLICATION

FLEXSTRIP

Jumpers are multi-

conductor board-to-board interconnect

devices, pre-plated and ready to use -

without wire stripping, cutting to length,

or solder preparation. They provide a

convenient, reliable alternative to

conventional point-to-point wiring for

high density, high-vibration PC board

interconnect applications.

FLEXSTRIP

Jumpers may be

repeatedly flexed without failure.

Flat/round conductor design and

one-piece

construction

give

vibration-proof reliability and longer

life than conventional wiring systems.

FLEXSTRIP

JUMPERS

ESIGN

DVANTAGES

• One-piece construction.

• Round copper conductors rolled

flat for high flex life, tin-plated for

easy soldering.

• Round-to-flat transition zone permits

flexing stress to be distributed

evenly throughout flat conductor area.

• Round-to-flat

design

provides

vibration-proof reliability and long life.

• Round-to-flat transition zone acts

as a hinge between PC boards;

allows boards to be opened for

fabrication and servicing, then

closed for compactness.

• Round pin ends facilitate PC board

insertion and long life.

• Choice of conductor pitch to

accommodate virtually any PCB

hole

pattern;

tightly

held

tolerances.

• Available in 4 insulations for high

volume commercial use as well as

military/aerospace applications.

• Jumpers may be “connectorized”

to mate with other industry-

standard headers.

• Jumpers may be used as part of

FLEXPAC

assemblies.

LR49571

E60980

Loop

Diameter

Flex Cycles

(in Millions)

Loop Diameter (inches)

Thomas & Betts Electronics/OEM Division Tel: 901-252-5000 Fax: 901-252-1312

157

Flexible Interconnections

Flexstrip

FLEXSTRIP

JUMPER ORDERING INFORMATION

Standard Jumpers

(Same termination on both ends)

FS N-1 2 A-70

Number of Conductors

Pin Arrangement

(for both ends)

A thru Z

(see above)

Insulation Length

.5" Min. to 34" Max. in

.050" increments

Product Code

Insulation Material

N – Nomex

T – Teflon

K – Kapton

P – Polyester

Conductor Pitch

1 – .050"

2 – .100"

3 – .125"

4 – .150"

5 – .200"

6 – .075"

7 – 2mm (.079")

8 – 1.25mm (.049")

9 – 1.0mm (.039")

Special Jumpers

(Different termination on each end)

Product Code

Insulation Material

N – Nomex

T – Teflon

K – Kapton

P – Polyester

Conductor Pitch

1 – .050"

2 – .100"

3 – .125"

4 – .150"

5 – .200"

6 – .075"

7 – 2mm (.079")

8 – 1.25mm (.049")

9 – 1.0mm (.039")

FS N - 1 3.25 G H - 20 V1

Special Pin

Length

.112"

.177

.134"

.079

.161"

TBD

.256"

V10 TBD

.122"

V11 .095

.150"

Pin Length Tol. +0.012/-0.008

Number of Conductors

(Max.recommended width 4 inches)

Pin Arrangement

(see above)

Right End

Left End

Insulation Length

.5" Min. to 34" Max. in

.050" increments

Thomas & Betts Electronics/OEM Division Tel: 901-252-5000 Fax: 901-252-1312

158

Flexible Interconnections

Flexstrip

OMEX

NSULATION

• An opaque aramid laminate that has excellent temperature

capability

• Can be installed by conventional soldering techniques

• Compatible with surface mount reflow soldering processes

• Suitable for most applications

• Resistant to damage from contact with a hot soldering

iron

• UL Style Number 5295

OLYESTER

NSULATION

• A lower temperature rated film that has excellent

mechanical and electrical properties

• Recommended for high humidity applications

• Recommended for use where controlled soldering

methods can be used

• Not recommended for surface mount reflow solder

applications

• UL Style Number 2639

EFLON

NSULATION

• A translucent film that has exceptional electrical and

chemical properties

• Can be installed by most commonly used soldering techniques

• Resistant to damage by contact with a hot soldering iron

• Recommended for high abrasion resistance applications

• Most commonly used for high electrical and mechanical

performance applications

• UL Style Number 2928

INSULATION MATERIAL

Conductor Pitch

Flammability Rating

APTON

NSULATION

• A distinctive amber film that is useful for all normal

soldering methods

• Dimensionally stable over a wide temperature and humidity

range

• Not damaged by accidental contact with a hot soldering iron

• Used in the most exacting applications

• UL Style Number 2927

POLYESTER

.100"

1 x 10

Ω

NOMEX

.100"

2 x 10

Ω

TEFLON

.100"

2 x 10

Ω

KAPTON

.100"

2 x 10

Ω

Equivalent Conductor Size

(American Wire Gauge)

Insulation Resistance

(gnd, sig, gnd) 12 inch

sample @ 500 VDC

Capacitance (picofarad/foot)

(gnd, sig, gnd)

Characteristic Impedance

Ω

(gnd, sig, gnd)

MID-PIN JUMPER THICKNESS

(.050), (.075), (.100), (.125), (.150), & (.200) PITCH

.254 (.010)

.406 (.016)

.254 (.010)

Nomex

Kapton

Teflon

Polyester

Temperature Rating

Current Rating

Voltage Rating

Min. Bend Radius

10.2 pF/ft

118Ω

105˚ C

3 amps

300 volts

1/8"

8.9 pF/ft

123Ω

125˚ C

3 amps

300 volts

1500 volts

1/8"

10.5 pF/ft

101Ω

150˚ C

3 amps

300 volts

1500 volts

1/8"

9.1 pF/ft

112Ω

150˚ C

3 amps

300 volts

1500 volts

1/8"

Min. Breakdown Voltage @ 1 min 1500 volts

No Ozone Depleting Substances Are Used in the Production Processes for Flexstrip Jumpers.

THICKNESS

WIRE

GAUGE

FOR PCB WITH THE

FOLLOWING DIAMETER

(±.001) HOLES AND

(±.005) CENTER TOLERANCE

—

.71 (.028)

.79 (.031)

.94 (.037)

NUMBER OF

CONDUCTORS

RECOMMENDED

(MIN. – MAX.)

2—70

2—60

2—45

2—35

2—30

2—22

PITCH

1.00 (.039)

1.25 (.049)

1.27 (.050)

1.90 (.075)

2.00 (.079)

2.54 (.100)

3.18 (.125)

3.81 (.150)

5.08 (.200)

MARGIN

.25 (.010)

.51 (.020)

(PIN END)

.64 (.025)

.84 (.033)

PIN DIA.

.320 (.0126)

.404 (.0159)

.511 (.0201)

Tolerance on pitch: ± .25mm (±.010), non-cumulative

Thomas & Betts Electronics/OEM Division Tel: 901-252-5000 Fax: 901-252-1312

Nomex, Teflon and Kapton are trademarks of E. I. DuPont de Nemours.

Dimensions shown are for reference only. Dimensions are in millimeters (inches).

159