Instant Internet
Evaluation Board
II-EVB-363MW/L/D/S/O
for Board rev. 3
User Manual
Version 1.20
Copyright © 2008,2009 Connect One Ltd.
International:
Connect One Ltd.
20 Atir Yeda Street
Kfar Saba 44643, Israel
Phone: +972-9-766-0456
Fax: +972-9-766-0461
Email: sales@connectone.com
http://www.connectone.com
USA:
Connect One Semiconductors, Inc.
560 S. Winchester Blvd.
Suite 500
San Jose, CA 95128
Tel: (408) 572-5675
Fax: (408) 572-5601
Connect One
Information provided by Connect One Ltd. is believed to be accurate and reliable.
However, Connect One assumes no responsibility for its use, nor any infringement of
patents or other rights of third parties, which may result from its use. No license is
granted by implication or otherwise under any patent rights of Connect One other than
for circuitry embodied in Connect One’s products. Connect One reserves the right to
change circuitry at any time without notice. This document is subject to change
without notice.
The software described in this document is furnished under a license agreement and
may be used or copied only in accordance with the terms of such a license agreement.
It is forbidden by law to copy the software on any medium except as specifically
allowed in the license agreement. No part of this document may be reproduced or
transmitted in any form or by any means, electronic or mechanical, including but not
limited to photocopying, recording, transmitting via fax and/or modem devices,
scanning, and/or information storage and retrieval systems for any purpose without
the express written consent of Connect One.
iChip, Nano WiReach, Nano LANReach, Nano Socket iWiFi, Nano Socket LAN, IP
Communication Controller, SerialNET, AT+i, and Connect One are trademarks of
Connect One Ltd.
Copyright
©
2008,2009 Connect One Ltd. All rights reserved.
II-EVB-363NW User’s Manual
2
Connect One
TABLE OF CONTENTS
Introduction............................................................................................................4
Unpacking ..............................................................................................................4
Connections............................................................................................................4
Installing the iChipConfig Utility & Evaluation Software ....................................5
Testing the WiFi module Wireless Connection .....................................................5
Testing the Nano LANReach/Socket LAN Connection ........................................6
Additional Connections .........................................................................................7
SPI Slave....................................................................................................................7
RJ45 10/100BaseT Ethernet LAN (for Nano WiReach/Socket iWiFi) .....................7
Connectors and Switch Positions...............................................................................8
8. II-EVB-363 Bill of Materials.................................................................................9
Appendix 1: II-EVB-363 Schematics : ..........................................................................9
Appendix 2: Nano WiReach Mechanical Views .........................................................13
Appendix 3: Nano LANReach Mechanical Views ......................................................14
Appendix 4: Installing USB Drivers on a PC ..............................................................15
Installing the USB driver: ........................................................................................15
Viewing the properties of the new driver: ...............................................................18
FAQs ........................................................................................................................20
Appendix 5: WiFi Configuration Notes.......................................................................21
Introduction..............................................................................................................21
iChip Wireless LAN Environment Configuration Parameters ................................22
Wireless LAN Configuration Web Site Page ..........................................................23
Wireless LAN Status Report....................................................................................23
iChip Wireless LAN Test Mode ..............................................................................24
Placement and Range Guidelines.............................................................................25
Wireless LAN Data Privacy/Security Considerations .............................................25
Appendix 6: SPI Host Interface ...................................................................................26
Introduction..............................................................................................................26
SPI Protocol .............................................................................................................26
Data from module to Host (Slave to Master)...........................................................26
Flow Control - Data from Host to iChip Flow Control ...........................................27
iSPIP — SPI GPIO Pin ............................................................................................27
iHIF — Host Interface .............................................................................................27
1.
2.
3.
4.
5.
6.
7.
II-EVB-363NW User’s Manual
3
Connect One
1.
Introduction
This manual is intended to familiarize customers with Connect One’s Instant Internet
Evaluation Board II-EVB-363. The II-EVB-363 is an evaluation platform for the
Nano WiReach™ WiFi Module, Nano LANReach™, Nano Socket iWiFi™ and Nano
SocketLAN™. The Connect One Nano and Socket modules are secure serial-to-WiFi
/ serial-to-LAN modules that also act as a bridge to connect serial devices to Ethernet
or 802.11b/g wireless LANs. The modules fit into a compact form factor and utilize
Connect One’s iChip CO2144 IP Communication Controller
™
and the AT+i
™
command set, a powerful set of Internet protocol commands developed by
Connect One to manage Internet connectivity through an Ethernet or wireless LAN
connection.
The modules enable sending and receiving textual and binary data, MIME-encoded
email messages; downloading HTML pages or files from a Web server, or items from
within a page; Web serving, as well as managing TCP or UDP socket
communications (with or without SSL3) over the Internet. They also include an FTP
client and a TELNET client.
Nano WiReach/Socket iWiFi can easily connect existing LAN based solutions to a
WiFi network when used in bridging mode.
Nano WiReach/Socket iWiFi support numerous WiFi security protocols such as
64/128-bit WEP encryption, AES-CCM and TKIP encryption, WPA (including AES)
and WPA2 in both PSK and Enterprise modes. The modules also support the
SSL3/TLS1 security protocols.
2.
Unpacking
Take the II-EVB-363 out of its box. Included in the box are:
•
The II-EVB-363 motherboard including
o
363MW: Nano WiReach module
o
363ML: Nano LANReach module
o
363MD: Both Nano modules
o
363MS: Nano SocketLAN module
o
363MO: Nano Socket iWiFi module
•
•
•
•
•
A serial cable with two DB-9 connectors
A USB cable
Antenna (in 363MW and 363MD)
+9VDC Power supply adaptor (110/220 VAC)
A single 30-pin female receptacle connector for prototyping on your own PCB
3.
Connections
1. Communications Cable:
•
Serial RS232:
Connect one end of the RS232 cable to the D-shell, 9-
pin female, Host RS232 port on the II-EVB-363 (J4) and connect the
other DB-9 connector to the COM1 or COM2 serial port on your PC,
or to the serial port of your embedded device.
II-EVB-363NW User’s Manual
4
Connect One
USB:
Connect one the device end of the USB cable to the EVB-363
USB connector (J1) and connect the other end to a Host USB port on
your PC or embedded device.
2. Connect the II-EVB-363 to the power supply.
3. Connect the WiFi antenna to the screw-on Antenna bracket.
•
4.
Installing the iChipConfig Utility & Evaluation Software
II-EVB-363 enables you to evaluate the modules without changing anything in your
current development environment. Using a simple terminal program on a PC, you can
issue AT+i commands to the module and get responses.
AT+i commands are used to configure parameter values into iChip’s flash memory
and activate Internet tasks such as Email send/Recieve, sockets, FTP sessions, Web,
and more.
A full description of the AT+i protocol can be found in the
AT+i Programmer’s
Manual
on the Connect One website at:
http://www.connectone.com/support.asp?did=42
To assist in configuring and evaluating the iChip and the modules, Connect One
supplies the iChipConfig Utility. This is a Windows-based GUI program that contains
intuitive dialog boxes to fully configure iChip. It doesn’t require any knowledge of
AT+i commands. In addition, it contains a local firmware upgrade function.
The iChipConfig Utility also allows you to perform specific Internet communication
tasks such as sending and receiving Emails, activating iChip’s websites, entering
SerialNET mode, and more.
For more information on the iChipConfig Utility and its usage, see the
iChip Config
Utility User’s Manual.
. The latest iChipConfig Utility version and user manual can be found on the
Connect One website in the
Support
section at:
http://www.connectone.com/support.asp?did=30
Most frequently iChipConfig connects to the II-EVB-363 though the PC’s standard
RS232 Serial port. The modules also include a USB Device port, which allows using
a USB connection as an alternative. To enable use of the PC USB port, a virtual COM
USB driver needs to be loaded on the PC. The iChipConfig can then be configured to
use the virtual port. Instructions for configuring the USB drivers on the PC are given
below in Appendix 3.
5.
Testing the WiFi module Wireless Connection
To test the wireless LAN connection, you need to configure the Nano
WiReach/Socket iWiFi to connect to an Access Point:
1. Make sure an Access Point is connected and configured properly.
2. Start the iChipConfig Utility on your PC.
3. In the main window of the utility, click the Dumb Terminal icon.
II-EVB-363NW User’s Manual
5
综合技术交流
