型号
  • 型号
  • 关键词
首页 > 器件类别 > 模拟混合信号IC > 放大器电路

LM2902WYDT

Operational Amplifiers - Op Amps 1.3MHz 100dB 375uA 20nA 2nA 800V

器件类别：模拟混合信号IC    放大器电路   

厂商名称：ST(意法半导体)

厂商官网：http://www.st.com/

下载文档
参数 预览 参数对比
LM2902WYDT 在线购买

供应商：

器件：LM2902WYDT

价格：-

最低购买：-

库存：点击查看

点击购买

器件参数
参数名称
属性值
Brand Name
STMicroelectronics
厂商名称
ST(意法半导体)
零件包装代码
SOIC
包装说明
SOP, SOP14,.25
针数
14
Reach Compliance Code
compliant
ECCN代码
EAR99
Factory Lead Time
10 weeks
放大器类型
OPERATIONAL AMPLIFIER
架构
VOLTAGE-FEEDBACK
最大平均偏置电流 (IIB)
0.3 µA
25C 时的最大偏置电流 (IIB)
0.15 µA
最小共模抑制比
70 dB
标称共模抑制比
80 dB
频率补偿
YES
最大输入失调电流 (IIO)
0.04 µA
最大输入失调电压
9000 µV
JESD-30 代码
R-PDSO-G14
长度
8.65 mm
低-偏置
NO
低-失调
NO
微功率
NO
负供电电压上限
标称负供电电压 (Vsup)
功能数量
4
端子数量
14
最高工作温度
125 °C
最低工作温度
-40 °C
封装主体材料
PLASTIC/EPOXY
封装代码
SOP
封装等效代码
SOP14,.25
封装形状
RECTANGULAR
封装形式
SMALL OUTLINE
包装方法
TR
峰值回流温度（摄氏度）
NOT SPECIFIED
电源
+-1.5/+-15/3/30 V
可编程功率
NO
认证状态
Not Qualified
筛选级别
AEC-Q100
座面最大高度
1.75 mm
最小摆率
0.24 V/us
标称压摆率
0.4 V/us
最大压摆率
1.2 mA
供电电压上限
32 V
标称供电电压 (Vsup)
5 V
表面贴装
YES
技术
BIPOLAR
温度等级
AUTOMOTIVE
端子形式
GULL WING
端子节距
1.27 mm
端子位置
DUAL
处于峰值回流温度下的最长时间
NOT SPECIFIED
标称均一增益带宽
1300 kHz
最小电压增益
50000
宽带
NO
宽度
3.9 mm
Base Number Matches
1
文档预览
LM2902W
Low-power quad operational amplifier
Datasheet - production data
Description
This circuit consists of four independent, high-
gain operational amplifiers which have frequency
compensation implemented internally and are
designed especially for automotive and industrial
control systems.
The device operates from a single power supply
over a wide range of voltages. Operation from
split power supplies is also possible and the low
power supply current drain is independent of the
magnitude of the power supply voltage.
All the pins are protected against electrostatic
discharges up to 800 V.
Features
Wide gain bandwidth: 1.3 MHz
Input common-mode voltage range includes
negative rail
Large voltage gain: 100 dB
Very low supply current per amplifier:
375 µA
Low input bias current: 20 nA
Low input offset current: 2 nA
ESD internal protection: 800 V
Wide power supply range
Single supply: 3 V to 30 V
Dual supplies: ±1.5 V to ±15 V
February 2016
DocID9922 Rev 10
1/19
www.st.com
This is information on a product in full production.
Contents
LM2902W
Contents
1
2
3
4
5
6
7
8
Schematic diagram.......................................................................... 3
Package pin connections................................................................ 4
Absolute maximum ratings and operating conditions ................. 5
Electrical characteristics ................................................................ 6
Electrical characteristic curves ...................................................... 8
Typical single-supply applications .............................................. 11
Macromodel ................................................................................... 13
Package information ..................................................................... 14
8.1
8.2
SO14 package information .............................................................. 15
TSSOP14 package information ....................................................... 16
9
10
Ordering information..................................................................... 17
Revision history ............................................................................ 18
2/19
DocID9922 Rev 10
LM2902W
Schematic
diagram
1
Schematic diagram
Figure 1: Schematic diagram (1/4 LM2902W)
DocID9922 Rev 10
3/19
Package pin
connections
LM2902W
2
Package pin connections
Figure 2: SO14 and TSSOP14 pin connections (top view)
4/19
DocID9922 Rev 10
LM2902W
Absolute
maximum ratings and operating
conditions
3
Absolute maximum ratings and operating conditions
Table 1: Absolute maximum ratings
Symbol
V
CC
V
id
V
i
I
in
T
stg
R
thja
Supply voltage
Differential input voltage
Input voltage
Output short-circuit to ground
Input current
(2)
(1)
Parameter
Value
±16 to 32
32
-0.3 to (V
CC
) + 0.3
Infinite
50
-65 to 150
(3)
+
Unit
V
mA
°C
Storage temperature range
Thermal resistance junction to ambient
(3)
SO14
TSSOP14
SO14
TSSOP14
105
100
31
32
800
100
V
°C/W
R
thjc
Thermal resistance junction to case
HBM: human body model
(4)
ESD
MM: machine model
(5)
(6)
CDM: charged device model
Notes:
(1)
1500
Short-circuits from the output to V
CC
can cause excessive heating and potential destruction. The maximum
+
output current is approximately 20 mA, independent of the magnitude of V
CC
(2)
+
This input current only exists when the voltage at any of the input leads is driven negative. It is due to the
collector-base junction of the input PNP transistor becoming forward biased and thereby acting as an input diode
clamp. In addition to this diode action, there is also NPN parasitic action on the IC chip. This transistor action can
cause the output voltages of the op amps to go to the V
CC
voltage level (or to ground for a large overdrive) for the
time during which an input is driven negative. This is not destructive and normal output is restored for input
voltages higher than -0.3 V.
(3)
(4)
R
thja/c
are typical values.
Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 kΩ
resistor between two pins of the device. This is done for all couples of connected pin combinations while the other
pins are floating.
(5)
Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two
pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of connected
pin combinations while the other pins are floating.
(6)
Charged device model: all pins and the package are charged together to the specified voltage and then
discharged directly to the ground through only one pin. This is done for all pins.
Table 2: Operating conditions
Symbol
V
CC
V
icm
T
oper
Supply voltage
-
Parameter
Value
3 to 30
(V
CC
) to (V
CC
) - 1.5
T
min
≤ T
amb
≤ T
max
(V
CC
) to (V
CC
) - 2
-40 to 125
-
+
+
Unit
Common mode input voltage range
Operating free-air temperature range
V
°C
DocID9922 Rev 10
5/19
查看更多>
参数对比
与LM2902WYDT相近的元器件有：LM2902WDT、LM2902WYPT、LM2902AWYPT、LM2902AWYDT。描述及对比如下：
型号 LM2902WYDT LM2902WDT LM2902WYPT LM2902AWYPT LM2902AWYDT
描述 Operational Amplifiers - Op Amps 1.3MHz 100dB 375uA 20nA 2nA 800V Operational Amplifiers - Op Amps CONDITIONING & INTERFACES Operational Amplifiers - Op Amps LP Quad 1.3MHz AMP 100 dB 375uA 800V Operational Amplifiers - Op Amps 1.3MHz 100dB 375uA 20nA 2nA 800V Operational Amplifiers - Op Amps 1.3MHz 100dB 375uA 20nA 2nA 800V
Brand Name STMicroelectronics STMicroelectronics STMicroelectronics - STMicroelectronics
厂商名称 ST(意法半导体) ST(意法半导体) ST(意法半导体) - ST(意法半导体)
零件包装代码 SOIC SOIC TSSOP - SOIC
包装说明 SOP, SOP14,.25 SOP, SOP14,.25 TSSOP, TSSOP14,.25 - SOP, SOP14,.25
针数 14 14 14 - 14
Reach Compliance Code compliant compliant compliant - compliant
ECCN代码 EAR99 EAR99 EAR99 - EAR99
Factory Lead Time 10 weeks 10 weeks 14 weeks - 10 weeks
放大器类型 OPERATIONAL AMPLIFIER OPERATIONAL AMPLIFIER OPERATIONAL AMPLIFIER - OPERATIONAL AMPLIFIER
架构 VOLTAGE-FEEDBACK VOLTAGE-FEEDBACK VOLTAGE-FEEDBACK - VOLTAGE-FEEDBACK
最大平均偏置电流 (IIB) 0.3 µA 0.3 µA 0.3 µA - 0.3 µA
25C 时的最大偏置电流 (IIB) 0.15 µA 0.15 µA 0.15 µA - 0.15 µA
最小共模抑制比 70 dB - 70 dB - 70 dB
标称共模抑制比 80 dB 80 dB 80 dB - 80 dB
频率补偿 YES YES YES - YES
最大输入失调电流 (IIO) 0.04 µA - 0.04 µA - 0.04 µA
最大输入失调电压 9000 µV 9000 µV 9000 µV - 4000 µV
JESD-30 代码 R-PDSO-G14 R-PDSO-G14 R-PDSO-G14 - R-PDSO-G14
长度 8.65 mm 8.65 mm 5 mm - 8.65 mm
低-偏置 NO - NO - NO
低-失调 NO NO NO - NO
微功率 NO YES NO - NO
功能数量 4 4 4 - 4
端子数量 14 14 14 - 14
最高工作温度 125 °C 125 °C 125 °C - 125 °C
最低工作温度 -40 °C -40 °C -40 °C - -40 °C
封装主体材料 PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY - PLASTIC/EPOXY
封装代码 SOP SOP TSSOP - SOP
封装等效代码 SOP14,.25 SOP14,.25 TSSOP14,.25 - SOP14,.25
封装形状 RECTANGULAR RECTANGULAR RECTANGULAR - RECTANGULAR
封装形式 SMALL OUTLINE SMALL OUTLINE SMALL OUTLINE, THIN PROFILE, SHRINK PITCH - SMALL OUTLINE
包装方法 TR TAPE AND REEL TR - TR
峰值回流温度（摄氏度） NOT SPECIFIED 260 260 - NOT SPECIFIED
电源 +-1.5/+-15/3/30 V +-1.5/+-15/3/30 V +-1.5/+-15/3/30 V - +-1.5/+-15/3/30 V
可编程功率 NO - NO - NO
认证状态 Not Qualified Not Qualified Not Qualified - Not Qualified
筛选级别 AEC-Q100 - AEC-Q100 - AEC-Q100
座面最大高度 1.75 mm 1.75 mm 1.2 mm - 1.75 mm
最小摆率 0.24 V/us 0.14 V/us 0.24 V/us - 0.24 V/us
标称压摆率 0.4 V/us 0.4 V/us 0.4 V/us - 0.4 V/us
最大压摆率 1.2 mA 3 mA 1.2 mA - 1.2 mA
供电电压上限 32 V 32 V 32 V - 32 V
标称供电电压 (Vsup) 5 V 5 V 5 V - 5 V
表面贴装 YES YES YES - YES
技术 BIPOLAR BIPOLAR BIPOLAR - BIPOLAR
温度等级 AUTOMOTIVE AUTOMOTIVE AUTOMOTIVE - AUTOMOTIVE
端子形式 GULL WING GULL WING GULL WING - GULL WING
端子节距 1.27 mm 1.27 mm 0.65 mm - 1.27 mm
端子位置 DUAL DUAL DUAL - DUAL
处于峰值回流温度下的最长时间 NOT SPECIFIED 40 40 - NOT SPECIFIED
标称均一增益带宽 1300 kHz 1300 kHz 1300 kHz - 1300 kHz
最小电压增益 50000 25000 50000 - 50000
宽带 NO - NO - NO
宽度 3.9 mm 3.9 mm 4.4 mm - 3.9 mm
热门器件
热门资源推荐
当控制板接近主回路板信号遇到干扰导致电感会叫，求指点一二 这个反相比例放大器怎么回事儿啊？ 这边二极管峰值检波器的几个参数不太懂？ N MOSFET VGS(th)和管子导通的关系 ？ 模拟示波器正常显示方波，其x轴扫描信号是 求助，多路光电二极管的信号复用直接用模拟开关可以吗？ D类功放的若干问题 十大失效分析技术 全国图像图形技术应用大会开始报名 二三极管参数及常用芯片及其他资料
PIC单片机控制的遥控防盗报警器电路 红外线探测报警器 使用ESP8266从NTP服务器获取时间并在OLED显示器上显示 开关电源的基本组成及工作原理 用NE555制作定时器 RS-485基础知识:处理空闲总线条件的两种常见方法 如何构建一个触摸传感器电路 如何调制IC555振荡器 基于ICL296的大电流开关稳压器电源电路 基于TDA2003的简单低功耗汽车立体声放大器电路
器件捷径:
L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ
需要登录后才可以下载。
登录取消