首页 > 器件类别 > 模拟混合信号IC > 信号电路

LM555CN/NOPB

IC PULSE; RECTANGULAR, TIMER, PDIP8, PLASTIC, DIP-8, Analog Waveform Generation Function

器件类别:模拟混合信号IC    信号电路   

厂商名称:National Semiconductor(TI )

厂商官网:http://www.ti.com

器件标准:

下载文档
器件参数
参数名称
属性值
是否Rohs认证
符合
厂商名称
National Semiconductor(TI )
包装说明
DIP, DIP8,.3
Reach Compliance Code
compliant
ECCN代码
EAR99
模拟集成电路 - 其他类型
PULSE; RECTANGULAR
JESD-30 代码
R-PDIP-T8
JESD-609代码
e3
长度
9.817 mm
湿度敏感等级
1
功能数量
1
端子数量
8
最高工作温度
70 °C
最低工作温度
封装主体材料
PLASTIC/EPOXY
封装代码
DIP
封装等效代码
DIP8,.3
封装形状
RECTANGULAR
封装形式
IN-LINE
峰值回流温度(摄氏度)
260
电源
5/15 V
认证状态
Not Qualified
座面最大高度
5.08 mm
最大供电电压 (Vsup)
16 V
最小供电电压 (Vsup)
4.5 V
标称供电电压 (Vsup)
5 V
表面贴装
NO
技术
BIPOLAR
温度等级
COMMERCIAL
端子面层
Matte Tin (Sn)
端子形式
THROUGH-HOLE
端子节距
2.54 mm
端子位置
DUAL
处于峰值回流温度下的最长时间
40
宽度
7.62 mm
文档预览
LM555 Timer
July 2006
LM555
Timer
General Description
The LM555 is a highly stable device for generating accurate
time delays or oscillation. Additional terminals are provided
for triggering or resetting if desired. In the time delay mode of
operation, the time is precisely controlled by one external
resistor and capacitor. For astable operation as an oscillator,
the free running frequency and duty cycle are accurately
controlled with two external resistors and one capacitor. The
circuit may be triggered and reset on falling waveforms, and
the output circuit can source or sink up to 200mA or drive
TTL circuits.
Features
n
n
n
n
n
n
n
n
n
Direct replacement for SE555/NE555
Timing from microseconds through hours
Operates in both astable and monostable modes
Adjustable duty cycle
Output can source or sink 200 mA
Output and supply TTL compatible
Temperature stability better than 0.005% per ˚C
Normally on and normally off output
Available in 8-pin MSOP package
Applications
n
n
n
n
n
n
n
Precision timing
Pulse generation
Sequential timing
Time delay generation
Pulse width modulation
Pulse position modulation
Linear ramp generator
Schematic Diagram
00785101
© 2006 National Semiconductor Corporation
DS007851
www.national.com
LM555
Connection Diagram
Dual-In-Line, Small Outline
and Molded Mini Small Outline Packages
00785103
Top View
Ordering Information
Package
8-Pin SOIC
8-Pin MSOP
8-Pin MDIP
Part Number
LM555CM
LM555CMX
LM555CMM
LM555CMMX
LM555CN
Package Marking
LM555CM
LM555CM
Z55
Z55
LM555CN
Media Transport
Rails
2.5k Units Tape and Reel
1k Units Tape and Reel
3.5k Units Tape and Reel
Rails
NSC Drawing
M08A
MUA08A
N08E
www.national.com
2
LM555
Absolute Maximum Ratings
(Note 2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage
Power Dissipation (Note 3)
LM555CM, LM555CN
LM555CMM
Operating Temperature Ranges
LM555C
Storage Temperature Range
0˚C to +70˚C
−65˚C to +150˚C
1180 mW
613 mW
+18V
Soldering Information
Dual-In-Line Package
Soldering (10 Seconds)
Small Outline Packages
(SOIC and MSOP)
Vapor Phase (60 Seconds)
Infrared (15 Seconds)
215˚C
220˚C
260˚C
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
Electrical Characteristics
(Notes 1, 2)
(T
A
= 25˚C, V
CC
= +5V to +15V, unless othewise specified)
Parameter
Conditions
Min
Supply Voltage
Supply Current
V
CC
= 5V, R
L
=
V
CC
= 15V, R
L
=
(Low State) (Note 4)
4.5
3
10
Limits
LM555C
Typ
Max
16
6
15
V
mA
Units
Timing Error, Monostable
Initial Accuracy
Drift with Temperature
Accuracy over Temperature
Drift with Supply
Timing Error, Astable
Initial Accuracy
Drift with Temperature
Accuracy over Temperature
Drift with Supply
Threshold Voltage
Trigger Voltage
Trigger Current
Reset Voltage
Reset Current
Threshold Current
Control Voltage Level
Pin 7 Leakage Output High
Pin 7 Sat (Note 7)
Output Low
Output Low
V
CC
= 15V, I
7
= 15mA
V
CC
= 4.5V, I
7
= 4.5mA
180
80
200
mV
mV
(Note 6)
V
CC
= 15V
V
CC
= 5V
9
2.6
0.4
V
CC
= 15V
V
CC
= 5V
R
A
, R
B
= 1k to 100kΩ,
C = 0.1µF, (Note 5)
3.0
0.30
0.667
5
1.67
0.5
0.5
0.1
0.1
10
3.33
1
0.9
1
0.4
0.25
11
4
100
%
%/V
x V
CC
V
V
µA
V
mA
µA
V
nA
2.25
150
%
ppm/˚C
R
A
= 1k to 100kΩ,
C = 0.1µF, (Note 5)
1.5
0.1
%
%/V
1
50
%
ppm/˚C
3
www.national.com
LM555
Electrical Characteristics
(Notes 1, 2)
(T
A
= 25˚C, V
CC
Parameter
(Continued)
= +5V to +15V, unless othewise specified)
Conditions
Min
Limits
LM555C
Typ
0.1
0.4
2
2.5
Max
0.25
0.75
2.5
V
V
V
V
V
0.25
12.5
12.75
2.75
13.3
3.3
100
100
0.35
V
V
V
V
ns
ns
Units
Output Voltage Drop (Low)
V
CC
= 15V
I
SINK
= 10mA
I
SINK
= 50mA
I
SINK
= 100mA
I
SINK
= 200mA
V
CC
= 5V
I
SINK
= 8mA
I
SINK
= 5mA
Output Voltage Drop (High)
I
SOURCE
= 200mA, V
CC
= 15V
I
SOURCE
= 100mA, V
CC
= 15V
V
CC
= 5V
Rise Time of Output
Fall Time of Output
Note 1:
All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 2:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 3:
For operating at elevated temperatures the device must be derated above 25˚C based on a +150˚C maximum junction temperature and a thermal
resistance of 106˚C/W (DIP), 170˚C/W (S0-8), and 204˚C/W (MSOP) junction to ambient.
Note 4:
Supply current when output high typically 1 mA less at V
CC
= 5V.
Note 5:
Tested at V
CC
= 5V and V
CC
= 15V.
Note 6:
This will determine the maximum value of R
A
+ R
B
for 15V operation. The maximum total (R
A
+ R
B
) is 20MΩ.
Note 7:
No protection against excessive pin 7 current is necessary providing the package dissipation rating will not be exceeded.
Note 8:
Refer to RETS555X drawing of military LM555H and LM555J versions for specifications.
www.national.com
4
LM555
Typical Performance Characteristics
Minimuim Pulse Width
Required for Triggering
Supply Current vs.
Supply Voltage
00785104
00785119
High Output Voltage vs.
Output Source Current
Low Output Voltage vs.
Output Sink Current
00785120
00785121
Low Output Voltage vs.
Output Sink Current
Low Output Voltage vs.
Output Sink Current
00785122
00785123
5
www.national.com
查看更多>
参数对比
与LM555CN/NOPB相近的元器件有:LM555CMX/NOPB、LM555CM/NOPB、LM555CMM/NOPB、LM555CMMX/NOPB。描述及对比如下:
型号 LM555CN/NOPB LM555CMX/NOPB LM555CM/NOPB LM555CMM/NOPB LM555CMMX/NOPB
描述 IC PULSE; RECTANGULAR, TIMER, PDIP8, PLASTIC, DIP-8, Analog Waveform Generation Function IC PULSE; RECTANGULAR, TIMER, PDSO8, SOIC-8, Analog Waveform Generation Function IC PULSE; RECTANGULAR, TIMER, PDSO8, SOIC-8, Analog Waveform Generation Function IC PULSE; RECTANGULAR, TIMER, PDSO8, 0.118 INCH, MINI, PLASTIC, SOIC-8, Analog Waveform Generation Function IC PULSE; RECTANGULAR, TIMER, PDSO8, 0.118 INCH, MINI, PLASTIC, SOIC-8, Analog Waveform Generation Function
是否Rohs认证 符合 符合 符合 符合 符合
厂商名称 National Semiconductor(TI ) National Semiconductor(TI ) National Semiconductor(TI ) National Semiconductor(TI ) National Semiconductor(TI )
包装说明 DIP, DIP8,.3 SOIC-8 SOIC-8 TSSOP, TSSOP8,.19 TSSOP, TSSOP8,.19
Reach Compliance Code compliant compliant compliant compliant compliant
ECCN代码 EAR99 EAR99 EAR99 EAR99 EAR99
模拟集成电路 - 其他类型 PULSE; RECTANGULAR PULSE; RECTANGULAR PULSE; RECTANGULAR PULSE; RECTANGULAR PULSE; RECTANGULAR
JESD-30 代码 R-PDIP-T8 R-PDSO-G8 R-PDSO-G8 S-PDSO-G8 S-PDSO-G8
JESD-609代码 e3 e3 e3 e3 e3
长度 9.817 mm 4.9 mm 4.9 mm 3 mm 3 mm
湿度敏感等级 1 1 1 1 1
功能数量 1 1 1 1 1
端子数量 8 8 8 8 8
最高工作温度 70 °C 70 °C 70 °C 70 °C 70 °C
封装主体材料 PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY
封装代码 DIP SOP SOP TSSOP TSSOP
封装等效代码 DIP8,.3 SOP8,.25 SOP8,.25 TSSOP8,.19 TSSOP8,.19
封装形状 RECTANGULAR RECTANGULAR RECTANGULAR SQUARE SQUARE
封装形式 IN-LINE SMALL OUTLINE SMALL OUTLINE SMALL OUTLINE, THIN PROFILE, SHRINK PITCH SMALL OUTLINE, THIN PROFILE, SHRINK PITCH
峰值回流温度(摄氏度) 260 260 260 260 260
电源 5/15 V 5/15 V 5/15 V 5/15 V 5/15 V
认证状态 Not Qualified Not Qualified Not Qualified Not Qualified Not Qualified
座面最大高度 5.08 mm 1.75 mm 1.75 mm 1.1 mm 1.1 mm
最大供电电压 (Vsup) 16 V 16 V 16 V 16 V 16 V
最小供电电压 (Vsup) 4.5 V 4.5 V 4.5 V 4.5 V 4.5 V
标称供电电压 (Vsup) 5 V 5 V 5 V 5 V 5 V
表面贴装 NO YES YES YES YES
技术 BIPOLAR BIPOLAR BIPOLAR BIPOLAR BIPOLAR
温度等级 COMMERCIAL COMMERCIAL COMMERCIAL COMMERCIAL COMMERCIAL
端子面层 Matte Tin (Sn) Matte Tin (Sn) Matte Tin (Sn) Matte Tin (Sn) Matte Tin (Sn)
端子形式 THROUGH-HOLE GULL WING GULL WING GULL WING GULL WING
端子节距 2.54 mm 1.27 mm 1.27 mm 0.65 mm 0.65 mm
端子位置 DUAL DUAL DUAL DUAL DUAL
处于峰值回流温度下的最长时间 40 40 40 40 40
宽度 7.62 mm 3.9 mm 3.9 mm 3 mm 3 mm
为什么要做RF射频测试?
无线产品一般测试的领域有电磁兼容EMC测试、RF射频测试,安规Safety测试,安全测试SAR测试...
兰博 RF/无线
[下载]怎样使用示波器测量电源开关损耗???
使用示波器测量电源开关损耗,文章不错。建议看看: 怎样使用示波器测量电源开关损耗??? 用示波器...
dontium 综合技术交流
急 求破解!困惑了几个星期了!
为啥用msp430驱动不了呢?用51就可以呢?msp430用的是默认的时钟!各位帮帮忙啊! /***...
smartboywe 微控制器 MCU
给大家一个封装库文件
protel的microchip封装 给大家一个封装库文件 这个很不错,下载了来看看。。对我的帮助很...
buanchao PCB设计
250-500V交流输入,8V,15mA直流输出的电源
各位大虾,本人要做一个250-500V交流输入,8V,15mA直流输出的电源。体积不能太大,采用哪种...
zd0515 电源技术
MSP430系列单片机系统工程设计与实践 源码及PDF电子书下载
以下PDF书和书中源代码,回复下载 本帖隐藏的内容 MSP430系列单片机系统...
Jacktang 微控制器 MCU
热门器件
热门资源推荐
器件捷径:
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ
需要登录后才可以下载。
登录取消