lithic power divider using M/A-COM’s GMIC technol-
ogy in a low cost SOIC-8 plastic package. This 3-
way power divider is ideally suited for applications
where small size, low insertion loss, superior phase/
amplitude tracking and low cost are required. Typi-
cal applications include personal communication
systems and other communication applications
where size and PCB real estate are at a
premium. Available in tape and reel.
The MAPDCC0006 is fabricated using a passive-
integrated circuit process. The process features full-
chip passivation for increased performance and reli-
ability.
Pin Configuration
Pin No.
1
2
3
4
Function
GND
RF IN
GND
GND
Pin No.
5
6
7
8
Function
RF3
GND
RF2
RF1
Ordering Information
Part Number
MAPDCC0006
MAPDCC0006TR
MAPDCC0006-TB
Package
Bulk Packaging
1000 piece reel
Sample Test Board
Note: Reference Application Note M513 for reel size
information.
Electrical Specifications: T
A
= 25°C
1
Parameter
Insertion Loss above 4.8 dB
Isolation
VSWR Input
Amplitude Balance
Phase Balance
Units
dB
dB
Ratio
dB
Deg.
Min
—
12
—
—
—
Typ
1.0
18
1.8:1
0.3
7
Max
1.4
—
2.0:1
0.6
14
1. All specifications apply with a 50-ohm source and load impedance.
1
* Restrictions on Hazardous Substances, European Union Directive 2002/95/EC.
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0006
Low Cost Three-Way GMIC SMT Power Divider,
1850 - 1990 MHz
Absolute Maximum Ratings
2,3
Parameter
Input Power
4
Operating Temperature
Storage Temperature
2.
3.
4.
Absolute Maximum
1W CW
-40°C to +85°C
-65°C to +150°C
Rev. V3
Recommended PIN Configuration
Exceeding any one or combination of these limits may cause
permanent damage to this device.
M/A-COM does not recommend sustained operation near
these survivability limits.
With internal load dissipation of 0.125W maximum.
Handling Procedures
Please observe the following precautions to avoid
damage:
Typical Performance Curves
Insertion Loss
(Dashed lines show amplitude balance window)
2.0
Static Sensitivity
Insertion Loss (dB)
GMIC Circuits are sensitive to electrostatic
discharge (ESD) and can be damaged by static
electricity. Proper ESD control techniques should
be used when handling these devices.
1.5
1.0
0.5
0.0
1850
1888
1925
1963
2000
Frequency (MHz)
VSWR
Isolation
2.0
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
1850
1888
1925
1963
2000
RF1-RF2
40
35
RF2-RF3
RF1-RF3
Isolation (dB)
30
25
20
15
10
5
0
1850
1888
1925
1963
2000
VSWR
Fre que ncy (MHz )
2
Fre que ncy (MHz )
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0006
Low Cost Three-Way GMIC SMT Power Divider,
1850 - 1990 MHz
Typical Performance Curves
Phase Balance (Relative to RF1)
RF1
10
8
6
RF2
RF3
Rev. V3
Phase (degrees)
4
2
0
-2
-4
-6
-8
-10
1850
1888
1925
1963
2000
Fre que ncy (MHz )
Lead-Free,
SOIC-8
†
†
3
Reference Application Note M538 for lead-free solder reflow
recommendations.
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0006
Low Cost Three-Way GMIC SMT Power Divider,
1850 - 1990 MHz
Rev. V3
M/A-COM Technology Solutions Inc. All rights reserved.
Information in this document is provided in connection with M/A-COM Technology Solutions Inc ("MACOM")
products. These materials are provided by MACOM as a service to its customers and may be used for
informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or
in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM
assumes no responsibility for errors or omissions in these materials. MACOM may make changes to
specifications and product descriptions at any time, without notice. MACOM makes no commitment to update
the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future
changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise,
to any intellectual property rights is granted by this document.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR
INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR
OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY
OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN
THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS,
WHICH MAY RESULT FROM THE USE OF THESE MATERIALS.
MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM
customers using or selling MACOM products for use in such applications do so at their own risk and agree to
fully indemnify MACOM for any damages resulting from such improper use or sale.
4
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
