19-1524; Rev 3; 2/01
UAL
IT MAN
TION K
A
SHEET
EVALU
S DATA
W
FOLLO
2.7V, Single-Supply, Cellular-Band
Linear Power Amplifiers
Features
o
Low Average CDMA Current Consumption in
Typical Urban Scenario
55mA (MAX2264)
90mA (MAX2265)
40mA (MAX2266)
o
0.5µA Shutdown Mode Eliminates External
Supply Switch
o
±0.8dB Gain Variation Over Temperature
o
No External Reference or Logic Interface
Circuitry Needed
o
Supply Current and ACPR Margin
Dynamically Adjustable
o
+2.7V to +5V Single-Supply Operation
o
37% Efficiency at +2.7V Operation
General Description
The MAX2264/MAX2265/MAX2266 power amplifiers are
designed for operation in IS-98-based CDMA, IS-136-
based TDMA, and PDC cellular telephones operating in
the 900MHz range. When matched for CDMA operation
and biased with margin over the adjacent and alternate
channel specification (-45dBc/-56dBc), the amplifiers
achieve 28dBm output power with 37% efficiency
(MAX2265). At +16dBm output—a very common power
level for CDMA phones—the MAX2265 still has 7% effi-
ciency, yielding excellent overall talk time. At the same
power level, the MAX2264/MAX2266 have an unprece-
dented 12%/17% efficiency, while still obtaining
32%/32% efficiency at maximum output power.
The MAX2264/MAX2265/MAX2266 have internally refer-
enced bias ports that are normally terminated with sim-
ple resistors. The bias ports allow customization of
ACPR margin and gain. They can also be used to
“throttle back” bias current when generating low power
levels. The MAX2264/MAX2265/MAX2266 have excel-
lent gain stability over temperature (±0.8dB), so
overdesign of driver stages and excess driver current
are dramatically reduced, further increasing the
phone’s talk time. The devices can be operated from
+2.7V to +5V while meeting all ACPR specifications
over the entire temperature range. Nonlinear efficiency
is 48% when matched for linear operation, or 55% when
matched for non-linear-only operation (MAX2265).
The devices are packaged in a 16-pin TSSOP with
exposed pad (EP). For module or direct chip attach
applications, the MAX2264 is also available in die form.
MAX2264/MAX2265/MAX2266
Ordering Information
PART
MAX2264EUE
MAX2264E/D
MAX2265EUE
MAX2266EUE
TEMP. RANGE
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PIN-
PACKAGE
16 TSSOP-EP
Dice*
16 TSSOP-EP
16 TSSOP-EP
TSSOP-EP
5mm x 6.4mm
*Contact
factory for dice specifications.
Applications
Cellular-Band CDMA Dual-Mode Phones
Cellular-Band PDC Phones
Cellular-Band TDMA Dual-Mode Phones
Dual-Mode Phones
2-Way Pagers
Power-Amplifier Modules
IN1 1
PWR 2
V
CC
3
Pin Configurations
TOP VIEW
MAX2264/MAX2266
16 IN0
15 BIAS2H
14 V
CC
BIAS
13 GND
12 NFP
11 OUT0
10 BIAS1L
9
OUT1
BIAS1H 4
Selector Guide
POWER-ADDED EFFICIENCY (%)
DEVICE
CDMA AT
+28dBm
32
37
32
CDMA AT
+16dBm
12
7
17
TDMA AT
+30dBm
—
42
—
V
CC
5
SHDN 6
BIAS2L 7
OUT1 8
MAX2264
MAX2265
MAX2266
TSSOP-EP
Pin Configurations continued at end of data sheet.
1
________________________________________________________________
Maxim Integrated Products
For price, delivery, and to place orders, please contact Maxim Distribution at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
2.7V, Single-Supply, Cellular-Band
Linear Power Amplifiers
MAX2264/MAX2265/MAX2266
ABSOLUTE MAXIMUM RATINGS
V
CC
to GND (no RF input) ....................................-0.3V to +6.5V
Logic Inputs to GND...................................-0.3V to (V
CC
+ 0.3V)
BIAS_ _ to GND ..........................................-0.3V to (V
CC
+ 0.3V)
RF Input Power .................................................+13dBm (20mW)
Logic Input Current...........................................................±10mA
Output VSWR with +13dBm Input ........................................2.5:1
Total DC Power Dissipation (T
PADDLE
= +100°C)
16-Pin TSSOP-EP (derate 60mW/°C
above T
PADDLE
= +100°C) ...............................................4W
θJA
...............................................................................8°C/W
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(V
CC
= +2.7V to +5V, T
A
= T
MIN
to T
MAX
, no input signal applied, V
SHDN
= 2.0V. Typical values are at V
CC
= +3.3V and T
A
= +25°C,
unless otherwise noted.) (Note 8)
PARAMETER
Operating Voltage Range
Idle Current
Shutdown Supply Current
Logic Input Current High
Logic Input Current Low
Logic Threshold High
Logic Threshold Low
SYMBOL
V
CC
I
CC
I
CC
MAX2264/MAX2266
MAX2265
SHDN
= PWR = GND
Logic = V
CC
Logic = GND
-1
-1
2.0
0.8
PWR = V
CC
PWR = GND
CONDITIONS
MIN
2.7
95
34
83
0.5
10
5
1
TYP
MAX
5.0
UNITS
V
mA
µA
µA
µA
V
V
AC ELECTRICAL CHARACTERISTICS—MAX2264
(MAX2264 EV kit, V
CC
= V
PWR
= V
SHDN
= +3.3V, T
A
= +25°C, f
IN
= 836MHz, CDMA modulation,
SHDN
= V
CC
, matching networks
tuned for 824MHz to 849MHz operation, 50Ω system, unless otherwise noted.)
PARAMETER
Frequency Range (Notes 1, 2)
Power Gain (Note 1)
Gain Variation vs. Temperature
(Note 1)
SYMBOL
f
IN
G
P
CONDITIONS
PWR = V
CC
or GND
PWR = V
CC
PWR = GND
T
A
= T
MIN
to T
MAX
, relative to T
A
= +25°C
PWR = V
CC
, P
IN
adjusted to meet ACPR
specification, f
IN
= 824MHz to 849MHz
PWR = V
CC
= 2.8V, P
IN
adjusted to meet
ACPR specification, f
IN
= 824MHz to 849MHz
PWR = GND, P
IN
adjusted to meet ACPR
specification, f
IN
= 824MHz to 849MHz
PWR = GND, V
CC
= 2.8V, P
IN
adjusted to meet
ACPR specification, f
IN
= 824MHz to 849MHz
27
26
15
14
T
A
= +25°C
T
A
= T
MIN
to T
MAX
MIN
824
23
22
18
21
±0.8
28
dBm
27
16.5
dBm
15.5
dB
24.5
dB
TYP
MAX
849
UNITS
MHz
Output Power
(High-Power Mode) (Note 1)
P
OUT
Output Power
(Low-Power Mode) (Note 1)
P
OUT
2
_______________________________________________________________________________________
2.7V, Single-Supply, Cellular-Band
Linear Power Amplifiers
AC ELECTRICAL CHARACTERISTICS—MAX2264 (continued)
(MAX2264 EV kit, V
CC
= V
PWR
= V
SHDN
= +3.3V, T
A
= +25°C, f
IN
= 836MHz, CDMA modulation,
SHDN
= V
CC
, matching networks
tuned for 824MHz to 849MHz operation, 50Ω system, unless otherwise noted.)
PARAMETER
AMPS Output Power (Note 1)
Adjacent-Channel Power Ratio
Limit (Notes 1, 2)
Alternate-Channel Power Ratio
Limit (Notes 1, 2)
SYMBOL
P
OUT
ACPR
ACPR
P
IN
= 8dBm
V
CC
= 2.8V to 5.0V, offset = 885kHz,
30kHz BW, f
IN
= 824MHz to 849MHz
V
CC
= 2.8V to 5.0V, offset = 1980kHz,
30kHz BW, f
IN
= 824MHz to 849MHz
PWR = V
CC
, P
IN
adjusted to meet ACPR
specification
PAE
PWR = GND, P
IN
adjusted to meet ACPR
specification
PAE
P
IN
= 8dBm
(Note 4)
PWR = V
CC
or GND
VSWR
f
IN
= 824MHz to 849MHz, PWR = GND or V
CC
P
IN
= 10dBm
Measured at 881MHz
PWR = GND, measured at 881MHz
Measured at 881MHz, P
IN
= 8dBm
(Note 7)
-139
-136
-138
32
12
44
550
1
2.4:1
-60
dBc
dBm/Hz
dBm/Hz
dBc
5
%
ns
µs
CONDITIONS
MIN
30.5
-44
-56
32
%
TYP
31
MAX
UNITS
dBm
dBc
dBc
MAX2264/MAX2265/MAX2266
Power-Added Efficiency
(Note 3)
AMPS Power-Added Efficiency
Power-Mode Switching Time
Turn-On Time (Notes 1, 4)
Maximum Input VSWR
Nonharmonic Spurious due
to Load Mismatch (Notes 1, 5)
Noise Power (Note 6)
AMPS Noise Power (Note 6)
Harmonic Suppression
AC ELECTRICAL CHARACTERISTICS—MAX2265
(MAX2265 EV kit, V
CC
= V
SHDN
= +3.3V, T
A
= +25°C, f
IN
= 836MHz, CDMA modulation, matching networks tuned for 824MHz to
849MHz operation, 50Ω system, unless otherwise indicated.)
PARAMETER
Frequency Range (Notes 1, 2)
Power Gain (Note 1)
Gain Variation vs. Temperature
(Note 1)
SYMBOL
f
IN
G
P
T
A
= +25°C
T
A
= T
MIN
to T
MAX
T
A
= T
MIN
to T
MAX
, relative to T
A
= +25°C
P
IN
adjusted to meet ACPR specification,
f
IN
= 824MHz to 849MHz
V
CC
= 2.8V, P
IN
adjusted to meet ACPR
specification, f
IN
= 824MHz to 849MHz
P
IN
= 8dBm
V
CC
= 2.8V to 5.0V, offset = 885kHz,
30kHz BW, f
IN
= 824MHz to 849MHz
V
CC
= 2.8V to 5.0V, offset = 1980kHz,
30kHz BW, f
IN
= 824MHz to 849MHz
27
26
30
-44
-56
CONDITIONS
MIN
824
24
23
±0.7
28
dBm
26.5
31
-45
-57
dBm
dBc
dBc
25.5
TYP
MAX
849
UNITS
MHz
dB
dB
Output Power (Note 1)
P
OUT
AMPS Output Power (Note 1)
Adjacent-Channel Power Ratio
(Notes 1, 2)
Alternate-Channel Power Ratio
(Notes 1, 2)
P
OUT
ACPR
ACPR
_______________________________________________________________________________________
3
2.7V, Single-Supply, Cellular-Band
Linear Power Amplifiers
MAX2264/MAX2265/MAX2266
AC ELECTRICAL CHARACTERISTICS—MAX2265 (continued)
(MAX2265 EV kit, V
CC
= V
SHDN
= +3.3V, T
A
= +25°C, f
IN
= 836MHz, CDMA modulation, matching networks tuned for 824MHz to
849MHz operation, 50Ω system, unless otherwise indicated.)
PARAMETER
Power-Added Efficiency
(Note 3)
AMPS Power-Added Efficiency
Turn-On Time (Notes 1, 4)
Maximum Input VSWR
Nonharmonic Spurious Due
to Load Mismatch (Notes 1, 5)
Noise Power (Note 6)
AMPS Noise Power (Note 6)
Harmonic Suppression
VSWR
f
IN
= 824MHz to 849MHz
P
IN
= 10dBm
Measured at 881MHz
Measured at 881MHz, P
IN
= 8dBm
(Note 7)
-140
-139
47
SYMBOL
PAE
PAE
CONDITIONS
P
IN
adjusted to give P
OUT
= 28dBm
P
IN
adjusted for P
OUT
= 16dBm
P
IN
= 8dBm
MIN
TYP
37
7
48
1
1.3:1
-60
dBc
dBm/Hz
dBm/Hz
dBc
5
MAX
UNITS
%
%
µs
AC ELECTRICAL CHARACTERISTICS—MAX2266
(MAX2266 EV kit, V
CC
= V
SHDN
= +3.3V, T
A
= +25°C, f
IN
= 836MHz, CDMA modulation, matching networks tuned for 824MHz to
849MHz operation, 50Ω system, unless otherwise indicated.)
PARAMETER
Frequency Range (Notes 1, 2)
Power Gain (Note 1)
Gain Variation vs. Temperature
(Note 1)
SYMBOL
f
IN
G
P
CONDITIONS
PWR = V
CC
or GND
PWR = V
CC
PWR = GND
T
A
= T
MIN
to T
MAX
, relative to T
A
= +25°C
PWR = V
CC
, P
IN
adjusted to meet ACPR
specification, f
IN
= 824MHz to 849MHz
PWR = V
CC
= 2.8V, P
IN
adjusted to meet
ACPR specification, f
IN
= 824MHz to 849MHz
PWR = GND, P
IN
adjusted to meet ACPR
specification, f
IN
= 824MHz to 849MHz
PWR = GND, V
CC
= 2.8V, P
IN
adjusted to meet
ACPR specification, f
IN
= 824MHz to 849MHz
P
IN
= 8dBm
V
CC
= 2.8V to 5.0V, offset = 885kHz,
30kHz BW, f
IN
= 824MHz to 849MHz
V
CC
= 2.8V to 5.0V, offset = 1980kHz,
30kHz BW, f
IN
= 824MHz to 849MHz
PWR = V
CC
, P
IN
adjusted to meet ACPR
specification
PAE
PWR = GND, P
IN
adjusted to meet ACPR
specification
17
27
26
14
13
31
-44
-56
32
%
T
A
= +25°C
T
A
= T
MIN
to T
MAX
MIN
824
24.5
23
25
27.5
±0.8
28
dBm
27
15.5
dBm
14
32
dBm
dBc
dBc
dB
26
dB
TYP
MAX
849
UNITS
MHz
Output Power
(High-Power Mode) (Note 1)
P
OUT
Output Power
(Low-Power Mode) (Note 1)
AMPS Output Power (Note 1)
Adjacent-Channel Power Ratio
Limit (Notes 1, 2)
Alternate-Channel Power Ratio
Limit (Notes 1, 2)
P
OUT
P
OUT
ACPR
ACPR
Power-Added Efficiency
(Note 3)
4
_______________________________________________________________________________________
2.7V, Single-Supply, Cellular-Band
Linear Power Amplifiers
AC ELECTRICAL CHARACTERISTICS—MAX2266 (continued)
(MAX2266 EV kit, V
CC
= V
PWR
= V
SHDN
= +3.3V, T
A
= +25°C, f
IN
= 836MHz, CDMA modulation,
SHDN
= V
CC
, matching networks
tuned for 824MHz to 849MHz operation, 50Ω system, unless otherwise noted.)
PARAMETER
AMPS Power-Added Efficiency
Power-Mode Switching Time
Turn-On Time (Notes 1, 4)
Maximum Input VSWR
Nonharmonic Spurious due
to Load Mismatch (Notes 1, 5)
Noise Power (Note 6)
AMPS Noise Power (Note 6)
Harmonic Suppression
VSWR
SYMBOL
PAE
P
IN
= 8dBm
(Note 4)
PWR = V
CC
or GND
f
IN
= 824MHz to 849MHz, PWR = GND or V
CC
P
IN
= 10dBm
Measured at 881MHz
PWR = GND, measured at 881MHz
Measured at 881MHz, P
IN
= 8dBm
(Note 7)
-137
-130
-136
32
CONDITIONS
MIN
TYP
48
550
1
2.4:1
-60
dBc
dBm/Hz
dBm/Hz
dBc
5
MAX
UNITS
%
ns
µs
MAX2264/MAX2265/MAX2266
Note 1:
Minimum and maximum values are guaranteed by design and characterization, not production tested.
Note 2:
P
MAX
is met over this frequency range at the ACPR limit with a single matching network. For optimum performance at other
frequencies, the output matching network must be properly designed. See the
Applications Information
section. Operation
between 750MHz and 1000MHz is possible but has not been characterized.
Note 3:
PAE is specified into a 50Ω load, while meeting ACPR requirements.
Note 4:
Time from logic transition until P
OUT
is within 1dB of its final mean power.
Note 5:
Murata isolator as load with 20:1 VSWR any phase angle after isolator.
Note 6:
Noise power can be improved by using the circuit in Figures 1, 2, and 3.
Note 7:
Harmonics measured on evaluation kit, which provides some harmonic attenuation in addition to the rejection provided by
the IC. The combined suppression is specified.
Note 8:
≥+25°C
guaranteed by production test,
≤+25°C
guaranteed through correlation to worst-case temperature testing.
Typical Operating Characteristics
(MAX2264/MAX2265/MAX2266 EV kits, V
CC
= +3.3V,
SHDN
= V
CC
, CDMA modulation, T
A
= +25°C, unless otherwise noted.)
MAX2264
SHUTDOWN CURRENT vs. SUPPLY VOLTAGE
MAX2264-01
MAX2264
GAIN vs. SUPPLY VOLTAGE
MAX2264-02
MAX2264
GAIN vs. SUPPLY VOLTAGE
PWR = GND
26
T
A
= -40°C
MAX2264-03
140
120
SUPPLY CURRENT (nA)
100
80
60
40
20
T
A
= -40°C
0
2.5
3.0
3.5
4.0
4.5
5.0
T
A
= +25°C
PWR = GND
SHDN = GND
NO INPUT DRIVE
T
A
= +85°C
30
PWR = V
CC
28
T
A
= -40°C
28
GAIN (dB)
26
GAIN (dB)
24
T
A
= +25°C
24
T
A
= +25°C
22
22
T
A
= +85°C
20
T
A
= +85°C
20
5.5
2.5
3.0
3.5
4.0
4.5
5.0
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
18
2.5
3.0
3.5
4.0
4.5
5.0
SUPPLY VOLTAGE (V)
_______________________________________________________________________________________
5
stm32/stm8
