PART NO.
ECN #
REV
A
REVISIONS
DESCRIPTION
RELEASED
DRAWN
DATE
CHECKD
Jagan
DATE
18/01/12
APPRVD
Farnell
DATE
01/02/12
MCD Series
-
Ashok
18/01/12
DS
PCB Layout
Schematic (Typical)
Dimensions : Millimetres (Inches)
(2, 4, 6, 8, 10 and 12 Pos Avails)
Important Notice :
This data sheet and its contents (the "Information") belong to the mem-
bers of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously sup-
plied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not oper-
ate to limit or restrict the Group's liability for death or personal injury resulting from its negli-
gence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
Jagan
APPROVED BY:
DATE:
18/01/12
DATE:
18/01/12
DATE:
01/02/12
DRAWING TITLE:
Switch - DS, DP, DA Series
SIZE
A
DWG NO.
M10001964
U.O.M.: mm
ELECTRONIC FILE
REV
73742_DWG
SHEET:
1
OF
A
SCALE: NTS
5
PART NO.
ECN #
REV
A
REVISIONS
DESCRIPTION
RELEASED
DRAWN
DATE
CHECKD
Jagan
DATE
18/01/12
APPRVD
Farnell
DATE
01/02/12
MCD Series
-
Ashok
18/01/12
DA
PCB Layout
Schematic (Typical)
Dimensions : Millimetres (Inches)
(4, 6 and 8 Pos Avails)
Important Notice :
This data sheet and its contents (the "Information") belong to the mem-
bers of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously sup-
plied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not oper-
ate to limit or restrict the Group's liability for death or personal injury resulting from its negli-
gence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
Veena
APPROVED BY:
DATE:
18/01/12
DATE:
18/01/12
DATE:
01/02/12
DRAWING TITLE:
Switch - DS, DP, DA Series
SIZE
A
DWG NO.
M10001964
U.O.M.: mm
ELECTRONIC FILE
REV
73742_DWG
SHEET:
2
OF
A
SCALE: NTS
5
PART NO.
ECN #
REV
A
REVISIONS
DESCRIPTION
RELEASED
DRAWN
DATE
CHECKD
Jagan
DATE
18/01/12
APPRVD
Farnell
DATE
01/02/12
MCD Series
-
Ashok
18/01/12
DP
PCB Layout
Schematic (Typical)
DP Series
Dimensions : Millimetres (Inches)
(4, 6 and 8 Pos Avails)
Important Notice :
This data sheet and its contents (the "Information") belong to the mem-
bers of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously sup-
plied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not oper-
ate to limit or restrict the Group's liability for death or personal injury resulting from its negli-
gence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
Veena
APPROVED BY:
DATE:
18/01/12
DATE:
18/01/12
DATE:
01/02/12
DRAWING TITLE:
Switch - DS, DP, DA Series
SIZE
A
DWG NO.
M10001964
U.O.M.: mm
ELECTRONIC FILE
REV
73742_DWG
SHEET:
3
OF
A
SCALE: NTS
5
PART NO.
ECN #
REV
A
REVISIONS
DESCRIPTION
RELEASED
DRAWN
DATE
CHECKD
Jagan
DATE
18/01/12
APPRVD
Farnell
DATE
01/02/12
MCD Series
-
Ashok
18/01/12
Specifications:
Mechanical:
Mechanical life
Maximum operation force
Stroke
Operation temperature
Storage temperature
Electrical:
Electrical life
Non-switching rating
Switching rating
Maximum contact resistance
Insulation resistance
Dielectric strength
Circuit
Materials:
Base
Colour
Cover
Colour
Actuators
Colour
Contact
Top seal
Potting material
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
2,000 operations per switch
400 gf (DP Series)
1,000gf maximum (DS and DA Series)
2 mm
-20°C to +70°C
-40°C to +85°C
2,000 operations per switch 24 V dc, 25 mA
100 mA, 50 V dc
25 mA, 24 V dc
50 mΩ at initial
100 MΩ
500 V ac for one minute
SPST
PBT thermoplastic
Black
PBT thermoplastic
Red, black and blue
PBT high thermoplastic
White
Phosphor bronze with gold plating over nickel
Polyester film
Epoxy
Soldering Process:
Keep all switch contacts in their “OFF” position for all operations
Wave soldering : Recommended temperature at 500°F (260°C) maximum 5 seconds for through hole type
Hand soldering : Use a soldering iron of 30 watts, controlled at 350°C approximately maximum 5 seconds
Make sure switch is in “OFF” position during soldering process, or it will decrease the operating force and meanwhile increase the contact resistance
Do not wash the switch body except top tape sealed type, which suitable for spray cleaning method from top of the s/w
Important Notice :
This data sheet and its contents (the "Information") belong to the mem-
bers of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously sup-
plied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not oper-
ate to limit or restrict the Group's liability for death or personal injury resulting from its negli-
gence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
Veena
APPROVED BY:
DATE:
18/01/12
DATE:
18/01/12
DATE:
01/02/12
DRAWING TITLE:
Switch - DS, DP, DA Series
SIZE
A
DWG NO.
M10001964
U.O.M.: mm
ELECTRONIC FILE
REV
73742_DWG
SHEET:
4
OF
A
SCALE: NTS
5
PART NO.
ECN #
REV
A
REVISIONS
DESCRIPTION
RELEASED
DRAWN
DATE
CHECKD
Jagan
DATE
18/01/12
APPRVD
Farnell
DATE
01/02/12
MCD Series
-
Ashok
18/01/12
Specification Table
Number of
Positions
4
6
8
4
6
8
2
10
12
4
6
8
A
11.52 (0.454)
16.60 (0.654)
21.68 (0.854)
11.52 (0.454)
16.60 (0.654)
21.68 (0.854)
6.44 (0.254)
26.76 (1.054)
31.84 (1.254)
11.72 (0.461)
16.80 (0.661)
21.88 (0.861)
B
7.62 (0.300)
12.70 (0.500)
17.78 (0.700)
7.62 (0.300)
12.70 (0.500)
17.78 (0.700)
2.54 (0.100)
22.86 (0.900)
27.94 (1.100)
7.62 (0.300)
12.70 (0.500)
17.78 (0.700)
Part Number
MCDA04
MCDA06
MCDA08
MCDS04
MCDS06
MCDS08
MCDS02
MCDS10
MCDS12
MCDP04
MCDP06
MCDP08
Dimensions : Millimetres (Inches)
Part Number Explanation:
MC
DA
04
Type Dip Switch
Number of Positions
www.element14.com
www.farnell.com
www.newark.com
Type Dip Switch
Number of Positions
:
DA = Right Angle, DP = Piano and DS = Slide Type Dip Switch
:
04 = 4, 06 = 6, 08 = 8, 02 = 2, 10 = 10 and 12 = 12 Positions
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
Veena
APPROVED BY:
DATE:
18/01/12
DATE:
18/01/12
DATE:
01/02/12
DRAWING TITLE:
Important Notice :
This data sheet and its contents (the "Information") belong to the mem-
bers of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously sup-
plied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not oper-
ate to limit or restrict the Group's liability for death or personal injury resulting from its negli-
gence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
Switch - DS, DP, DA Series
SIZE
A
DWG NO.
M10001964
U.O.M.: mm
ELECTRONIC FILE
REV
73742_DWG
SHEET:
5
OF
A
SCALE: NTS
5
WindowsCE
