型号
  • 型号
  • 关键词
首页 > 器件类别 > 半导体 > 逻辑

MCP4542-502E/UN

10K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 129 POSITIONS, PDSO8
10K 数字电位器, 递增/递减控制接口, 129 位置, PDSO8

器件类别：半导体    逻辑   

厂商名称：Microchip(微芯科技)

厂商官网：https://www.microchip.com

下载文档
参数 预览
器件参数
参数名称
属性值
功能数量
1
端子数量
8
最大工作温度
125 Cel
最小工作温度
-40 Cel
额定供电电压
2.7 V
额定带宽
1 MHz
额定总电阻
10000 ohm
加工封装描述
PLASTIC, MSOP-8
无铅
Yes
欧盟RoHS规范
Yes
中国RoHS规范
Yes
状态
ACTIVE
包装形状
SQUARE
包装尺寸
SMALL OUTLINE, THIN PROFILE, SHRINK PITCH
表面贴装
Yes
端子形式
GULL WING
端子间距
0.6500 mm
端子涂层
MATTE TIN
端子位置
DUAL
包装材料
PLASTIC/EPOXY
温度等级
AUTOMOTIVE
转换器的类型
DIGITAL POTENTIOMETER
电阻率
LINEAR
控制接口
INCREMENT/DECREMENT
方位数
129
额定温度系数
150 ppm/Cel
最大终端电阻电压
5.5 V
最小终端电阻电压
0.0 V
文档预览
MCP454X/456X/464X/466X
7/8-Bit Single/Dual I
2
C Digital POT with
Nonvolatile Memory
Features
• Single or Dual Resistor Network Options
• Potentiometer or Rheostat Configuration Options
• Resistor Network Resolution
- 7-bit: 128 Resistors (129 Steps)
- 8-bit: 256 Resistors (257 Steps)
• R
AB
Resistances Options of:
- 5 k
- 10 k
- 50 k
- 100 k
• Zero-Scale to Full-Scale Wiper Operation
• Low Wiper Resistance: 75 (typical)
• Low Tempco:
- Absolute (Rheostat): 50 ppm typical
(0°C to 70°C)
- Ratiometric (Potentiometer): 15 ppm typical
• Nonvolatile Memory
- Automatic Recall of Saved Wiper Setting
- WiperLock™ Technology
- 10 General Purpose Memory Locations
• I
2
C Serial Interface
- 100 kHz, 400 kHz and 3.4 MHz Support
• Serial Protocol Allows:
- High-Speed Read/Write to Wiper
- Read/Write to EEPROM
- Write Protect to be Enabled/Disabled
- WiperLock to be Enabled/Disabled
• Resistor Network Terminal Disconnect Feature
via the Terminal Control (TCON) Register
• Write Protect Feature:
- Hardware Write Protect (WP) Control Pin
- Software Write Protect (WP) Configuration Bit
• Brown-out Reset Protection (1.5V typical)
• Serial Interface Inactive Current (2.5 uA typical)
• High-Voltage Tolerant Digital Inputs: Up to 12.5V
• Wide Operating Voltage:
- 2.7V to 5.5V - Device Characteristics Specified
- 1.8V to 5.5V - Device Operation
• Wide Bandwidth (-3dB) Operation:
- 2 MHz (typ.) for 5.0 k Device
• Extended Temperature Range (-40°C to +125°C)
Description
The MCP45XX and MCP46XX devices offer a wide
range of product offerings using an I
2
C interface. This
family of devices support 7-bit and 8-bit resistor
networks, nonvolatile memory configurations, and
Potentiometer and Rheostat pinouts.
WiperLock Technology allows application-specific
calibration settings to be secured in the EEPROM.
Package Types (top view)
MCP45X1
Single Potentiometer
HVC / A0
SCL
SDA
V
SS
1
2
3
4
8
7
6
5
V
DD
P0B
P0W
P0A
MCP45X2
Single Rheostat
HVC / A0
SCL
SDA
V
SS
1
2
3
4
8
7
6
5
V
DD
A1
P0B
P0W
MSOP
HVC / A0 1
SCL 2
SDA 3
V
SS
4
EP
9
8 V
DD
7 P0B
6 P0W
5 P0A
HVC / A0 1
SCL 2
SDA 3
V
SS
4
MSOP
8 V
DD
EP
9
7 A1
6 P0B
5 P0W
DFN 3x3 (MF) *
DFN 3x3 (MF) *
MCP46X1
Dual Potentiometers
HVC/A0
SCL
SDA
V
SS
P1B
P1W
P1A
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
DD
A1
A2
WP
P0B
P0W
P0A
HVC/A0
V
DD
A1
A2
16 15 14 13
SCL
SDA
V
SS
V
SS
1
2
3
4
EP
17
5 6 7 8
P1B
P1W
P1A
P0A
12 WP
11 NC
10 P0B
9 P0W
TSSOP
QFN-16 4x4 (ML) *
MCP46X2
Dual Rheostat
HVC/A0
SCL
SDA
V
SS
P1B
1
2
3
4
5
10 V
DD
HVC / A0 1
9 A1
SCL 2
8 P0B
SDA 3
7 P0W
V
SS
4
6 P1W
P1B 5
10 V
DD
EP
11
9 A1
8 P0B
7 P0W
6 P1W
MSOP
DFN 3x3 (MF) *
* Includes Exposed Thermal Pad (EP); see
Table 3-1.
2008-2013 Microchip Technology Inc.
DS22107B-page 1
MCP454X/456X/464X/466X
Device Block Diagram
V
DD
V
SS
A2
A1
HVC/A0
SCL
I
2
C Interface
SDA
WP
Memory (16x9)
Wiper0 (V & NV)
Wiper1 (V & NV)
TCON
STATUS
Data EEPROM
(10 x 9-bits)
Power-up/
Brown-out
Control
I C Serial
Interface
Module &
Control
Logic
(WiperLock™
Technology)
2
Resistor
Network 0
(Pot 0)
Wiper 0
& TCON
Register
P0A
P0W
P0B
P1A
Resistor
Network 1
(Pot 1)
Wiper 1
& TCON
Register
P1W
P1B
For Dual Resistor Network
Devices Only
Device Features
WiperLock
Technology
POR Wiper
Setting
# of Steps
# of POTs
Control
Interface
Memory
Type
Resistance (typical)
R
AB
Options (k)
Wiper
- R
W
()
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
V
DD
Operating
Range
(2)
Device
Wiper
Configuration
MCP4531
(3)
MCP4532
(3)
MCP4541
MCP4542
MCP4551
(3)
MCP4552
(3)
MCP4561
MCP4562
MCP4631
(3)
MCP4632
MCP4641
MCP4642
MCP4651
(3)
MCP4652
(3)
MCP4661
MCP4662
Note 1:
2:
3:
(3)
1 Potentiometer
(1)
1
1
1
1
2
2
2
2
2
Rheostat
(1)
I
2
C
I
2
C
I
2
C
I
2
C
I
2
C
I
2
C
I
2
C
I
2
C
2
RAM
RAM
EE
EE
RAM
RAM
EE
EE
RAM
RAM
EE
EE
RAM
RAM
EE
EE
No
No
Yes
Yes
No
No
Yes
Yes
No
No
Yes
Yes
No
No
Yes
Yes
Mid-Scale 5.0, 10.0, 50.0, 100.0
Mid-Scale 5.0, 10.0, 50.0, 100.0
NV Wiper 5.0, 10.0, 50.0, 100.0
NV Wiper 5.0, 10.0, 50.0, 100.0
Mid-Scale 5.0, 10.0, 50.0, 100.0
Mid-Scale 5.0, 10.0, 50.0, 100.0
NV Wiper 5.0, 10.0, 50.0, 100.0
NV Wiper 5.0, 10.0, 50.0, 100.0
Mid-Scale 5.0, 10.0, 50.0, 100.0
Mid-Scale 5.0, 10.0, 50.0, 100.0
NV Wiper 5.0, 10.0, 50.0, 100.0
NV Wiper 5.0, 10.0, 50.0, 100.0
Mid-Scale 5.0, 10.0, 50.0, 100.0
Mid-Scale 5.0, 10.0, 50.0, 100.0
NV Wiper 5.0, 10.0, 50.0, 100.0
NV Wiper 5.0, 10.0, 50.0, 100.0
129 1.8V to 5.5V
129 1.8V to 5.5V
129 2.7V to 5.5V
129 2.7V to 5.5V
257 1.8V to 5.5V
257 1.8V to 5.5V
257 2.7V to 5.5V
257 2.7V to 5.5V
129 1.8V to 5.5V
129 1.8V to 5.5V
129 2.7V to 5.5V
129 2.7V to 5.5V
257 1.8V to 5.5V
257 1.8V to 5.5V
257 2.7V to 5.5V
257 2.7V to 5.5V
1 Potentiometer
Rheostat
Rheostat
Rheostat
1 Potentiometer
(1)
1 Potentiometer
(1)
Potentiometer
(1)
Rheostat
Rheostat
Rheostat
(1)
I
2
C
I C
I
2
C
I
2
C
I
2
C
I
2
C
I
2
C
I
2
C
2 Potentiometer
(1)
2 Potentiometer
(1)
2 Potentiometer
Rheostat
Floating either terminal (A or B) allows the device to be used as a Rheostat (variable resistor).
Analog characteristics only tested from 2.7V to 5.5V unless otherwise noted.
Please check Microchip web site for device release and availability
DS22107B-page 2
2008-2013 Microchip Technology Inc.
MCP454X/456X/464X/466X
1.0
1.1
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings†
Voltage on V
DD
with respect to V
SS
........................................................................................................... -0.6V to +7.0V
Voltage on HVC/A0, A1, A2, SCL, SDA and WP with respect to V
SS
....................................................... -0.6V to 12.5V
Voltage on all other pins (PxA, PxW, and PxB) with respect to V
SS
..................................................-0.3V to V
DD
+ 0.3V
Input clamp current, I
IK
(V
I
< 0, V
I
> V
DD
, V
I
> V
PP ON
HV pins)........................................................................... ±20 mA
Output clamp current, I
OK
(V
O
< 0 or V
O
> V
DD
) .................................................................................................. ±20 mA
Maximum output current sunk by any Output pin....................................................................................................25 mA
Maximum output current sourced by any Output pin .............................................................................................25 mA
Maximum current out of V
SS
pin ...........................................................................................................................100 mA
Maximum current into V
DD
pin ..............................................................................................................................100 mA
Maximum current into P
X
A, P
X
W & P
X
B pins ...................................................................................................... ±2.5 mA
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied................................................................................................-40°C to +125°C
Package power dissipation (T
A
= +50°C, T
J
= +150°C)
MSSOP-8 .......................................................................................................................................................473 mW
MSSOP-10 .....................................................................................................................................................495 mW
DFN-8 (3x3) ......................................................................................................................................................1.76W
DFN-10 (3x3) ....................................................................................................................................................1.87W
TSSOP-14.........................................................................................................................................................1.00W
QFN-16 (4x4) ....................................................................................................................................................2.18W
Soldering temperature of leads (10 seconds) ....................................................................................................... +300°C
ESD protection on all pins
4
kV (HBM),
300V
(MM)
Maximum Junction Temperature (T
J
) ................................................................................................................... +150°C
† Notice:
Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. This
is a stress rating only and functional operation of the device at those or any other conditions above those indicated in
the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended peri-
ods may affect device reliability.
2008-2013 Microchip Technology Inc.
DS22107B-page 3
MCP454X/456X/464X/466X
AC/DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C
T
A
+125°C (extended)
DC Characteristics
All parameters apply across the specified operating ranges unless noted.
V
DD
= +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices.
Typical specifications represent values for V
DD
= 5.5V, T
A
= +25°C.
Sym
V
DD
V
HV
Min
2.7
1.8
HVC pin voltage
range
V
SS
V
SS
V
DD
Start Voltage
to ensure Wiper
Reset
V
DD
Rise Rate to
ensure Power-on
Reset
Delay after device
exits the reset state
(V
DD
> V
BOR
)
Supply Current
(Note
10)
V
BOR
—
Typ
—
—
—
—
—
Max
5.5
2.7
12.5V
V
DD
+
8.0V
1.65
Units
V
V
V
V
V
Serial Interface only.
V
DD
The HVC pin will be at one
4.5V of three input levels
V < (V
IL
, V
IH
or V
IHH
). (Note
6)
DD
Parameters
Supply Voltage
Conditions
4.5V
RAM retention voltage (V
RAM
) < V
BOR
V
DDRR
(Note
9)
V/ms
T
BORD
—
10
20
µs
I
DD
—
—
600
µA
Serial Interface Active,
HVC/A0 = V
IH
(or V
IL
) (Note
11)
Write all
0’s
to Volatile Wiper 0
V
DD
= 5.5V, F
SCL
= 3.4 MHz
Serial Interface Active,
HVC/A0 = V
IH
(or V
IL
) (Note
11)
Write all
0’s
to Volatile Wiper 0
V
DD
= 5.5V, F
SCL
= 100 kHz
EE Write Current (Write Cycle)
(Nonvolatile device only),
V
DD
= 5.5V, F
SCL
= 400 kHz,
Write all
0’s
to Nonvolatile Wiper 0
SCL = V
IL
or V
IH
Serial Interface Inactive,
(Stop condition, SCL = SDA = V
IH
),
Wiper = 0
V
DD
= 5.5V, HVC/A0 = V
IH
—
—
250
µA
—
—
575
µA
—
2.5
5
µA
Note 1:
2:
3:
4:
5:
6:
7:
Resistance is defined as the resistance between terminal A to terminal B.
INL and DNL are measured at V
W
with V
A
= V
DD
and V
B
= V
SS
.
MCP4XX1
only.
MCP4XX2
only, includes V
WZSE
and V
WFSE
.
Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
This specification by design.
Non-linearity is affected by wiper resistance (R
W
), which changes significantly overvoltage and
temperature.
8:
The
MCP4XX1
is externally connected to match the configurations of the
MCP45X2
and
MCP46X2,
and
then tested.
9:
POR/BOR is not rate dependent.
10:
Supply current is independent of current through the resistor network.
11:
When HVC/A0 = V
IHH
, the I
DD
current is less due to current into the HVC/A0 pin. See I
PU
specification.
DS22107B-page 4
2008-2013 Microchip Technology Inc.
MCP454X/456X/464X/466X
AC/DC CHARACTERISTICS (CONTINUED)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C
T
A
+125°C (extended)
DC Characteristics
All parameters apply across the specified operating ranges unless noted.
V
DD
= +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices.
Typical specifications represent values for V
DD
= 5.5V, T
A
= +25°C.
Sym
R
AB
Min
4.0
8.0
40.0
80.0
Resolution
Step Resistance
N
R
S
—
—
Nominal
Resistance Match
|R
AB0
- R
AB1
| /
R
AB
|R
BW0
- R
BW1
|
/ R
BW
Wiper Resistance
(Note
3, Note 4)
Nominal
Resistance
Tempco
Ratiometeric
Tempco
Resistor Terminal
Input Voltage
Range (Terminals
A, B and W)
Note 1:
2:
3:
4:
5:
6:
7:
R
W
R
AB
/T
—
—
—
—
—
—
—
V
WB
/T
V
A,
V
W,
V
B
—
Vss
Typ
5
10
50
100
257
129
R
AB
/
(256)
R
AB
/
(128)
0.2
0.25
75
75
50
100
150
15
—
—
—
1.25
1.5
160
300
—
—
—
—
V
DD
Max
6.0
12.0
60.0
120.0
Units
k
k
k
k
Taps
Taps
%
%
Conditions
-502 devices(Note
1)
-103 devices(Note
1)
-503 devices(Note
1)
-104 devices(Note
1)
8-bit
7-bit
8-bit
7-bit
No Missing Codes
No Missing Codes
Note 6
Note 6
Parameters
Resistance
(± 20%)
MCP46X1
devices only
MCP46X2
devices only,
Code = Full-Scale
V
DD
= 5.5 V, I
W
= 2.0 mA, code = 00h
V
DD
= 2.7 V, I
W
= 2.0 mA, code = 00h
ppm/°C T
A
= -20°C to +70°C
ppm/°C T
A
= -40°C to +85°C
ppm/°C T
A
= -40°C to +125°C
ppm/°C Code = Mid-scale (80h or 40h)
V
Note 5, Note 6
Resistance is defined as the resistance between terminal A to terminal B.
INL and DNL are measured at V
W
with V
A
= V
DD
and V
B
= V
SS
.
MCP4XX1
only.
MCP4XX2
only, includes V
WZSE
and V
WFSE
.
Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
This specification by design.
Non-linearity is affected by wiper resistance (R
W
), which changes significantly overvoltage and
temperature.
8:
The
MCP4XX1
is externally connected to match the configurations of the
MCP45X2
and
MCP46X2,
and
then tested.
9:
POR/BOR is not rate dependent.
10:
Supply current is independent of current through the resistor network.
11:
When HVC/A0 = V
IHH
, the I
DD
current is less due to current into the HVC/A0 pin. See I
PU
specification.
2008-2013 Microchip Technology Inc.
DS22107B-page 5
查看更多>
热门器件
热门资源推荐
PIC单片机控制的遥控防盗报警器电路 红外线探测报警器 使用ESP8266从NTP服务器获取时间并在OLED显示器上显示 开关电源的基本组成及工作原理 用NE555制作定时器 RS-485基础知识:处理空闲总线条件的两种常见方法 如何构建一个触摸传感器电路 如何调制IC555振荡器 基于ICL296的大电流开关稳压器电源电路 基于TDA2003的简单低功耗汽车立体声放大器电路
器件捷径:
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ
需要登录后才可以下载。
登录取消