MLP2012R1R0MT0S1,MLP2012R1R0MT0S1 pdf中文资料,MLP2012R1R0MT0S1引脚图,MLP2012R1R0MT0S1电路-Datasheet-电子工程世界

文档预览

I N D U C T O R S

April 2018

Inductors for power circuits

Multilayer ferrite

MLP series

MLP2012

type

MLP2012

2012 [0805 inch]*

Dimensions Code JIS[EIA]

(2/17)

I N D U C T O R S

REMINDERS FOR USING THESE PRODUCTS

Before using these products, be sure to request the delivery specifications.

SAFETY REMINDERS

Please pay sufficient attention to the warnings for safe designing when using these products.

REMINDERS

The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH

or less).

If the storage period elapses, the soldering of the terminal electrodes may deteriorate.

Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).

Before soldering, be sure to preheat components.

The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature

does not exceed 150°C.

Soldering corrections after mounting should be within the range of the conditions determined in the specifications.

If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.

When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to

the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.

Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal

design.

Carefully lay out the coil for the circuit board design of the non-magnetic shield type.

A malfunction may occur due to magnetic interference.

Use a wrist band to discharge static electricity in your body through the grounding wire.

Do not expose the products to magnets or magnetic fields.

Do not use for a purpose outside of the contents regulated in the delivery specifications.

The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications

equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement

equipment, industrial robots) under a normal operation and use condition.

The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or

quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to

society, person or property.

If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions

set forth in the each catalog, please contact us.

(1) Aerospace/Aviation equipment

(2) Transportation equipment (cars, electric trains, ships, etc.)

(3) Medical equipment

(4) Power-generation control equipment

(5) Atomic energy-related equipment

(6) Seabed equipment

(7) Transportation control equipment

(8) Public information-processing equipment

(9) Military equipment

(10) Electric heating apparatus, burning equipment

(11) Disaster prevention/crime prevention equipment

(12) Safety equipment

(13) Other applications that are not considered general-purpose

applications

When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing

protection circuit/device or providing backup circuits in your equipment.

20180424 / inductor_commercial_power_mlp2012_en.fm

(3/17)

I N D U C T O R S

Inductors for power circuits

Multilayer ferrite

Product compatible with RoHS directive

Halogen-free

Compatible with lead-free solders

Overview of MLP2012 type

FEATURES

A low-loss magnetic material is used so that a low-loss inductor for the power supply circuit can be achieved.

In addition to the inductance value, product types with various features are available so that they can be compatible with different

usages.

H type: This product uses a low-loss material and has low DC resistance.

* Optimal for when heavy load power efficiency is important.

V type: As with the H type, this product with a low-loss magnetic material and that has good DC superimposition type characteristics.

* Optimal for when light load power efficiency is important.

S type: STD product lineup that includes a wide L value and various sizes.

APPLICATION

Smart phones, tablet terminals, digital cameras, video cameras, HDDs, power supply modules, etc.

PART NUMBER CONSTRUCTION

MLP

Series name

2012

L×W Dimensions

(mm)

2012

2.0×1.25

Characteristic type

Low core loss

(Emphasized DC

resistance)

Low core loss

(Emphasized DC

bias characteristics)

STD product

R47

Inductance

(µH)

R47

1R0

0.47

1.0

Height

(mm max.)

0.55

1.0

Packaging style

Taping

0S1

Internal code

0S1

OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT

Temperature range

Type

Operating

temperature



（°C）

Storage

temperature



（°C）

Package quantity

Individual weight

(pieces/reel)

4,000

t=0.55

MLP2012

–40 to +125

–40 to +85

t=1.0



Operating temperature range includes self-temperature rise.



The Storage temperature range is for after the circuit board is mounted.

（mg）

RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html

Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.

Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.

Please note that the contents may change without any prior notice due to reasons such as upgrading.

20180424 / inductor_commercial_power_mlp2012_en.fm

(4/17)

I N D U C T O R S

MLP2012 type

RECOMMENDED REFLOW PROFILE

Preheating

Soldering

Peak

Natural

cooling

Temperature

Time

Preheating

Temp.

150°C

180°C

Time

60 to 120s

Soldering

Temp.

Time

230°C

30 to 60s

Peak

Temp.

250 to 260°C

Time

10s max.

Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.

Please note that the contents may change without any prior notice due to reasons such as upgrading.

20180424 / inductor_commercial_power_mlp2012_en.fm

(5/17)

I N D U C T O R S

MLP2012 type

SHAPE & DIMENSIONS

1.25

0.20

0.50

0.30

2.00

0.20

0.50

0.30

0.50±0.05

0.85±0.15

Dimensions in mm

RECOMMENDED LAND PATTERN

0.8

1.0

0.8

Dimensions in mm

Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.

Please note that the contents may change without any prior notice due to reasons such as upgrading.

1.2

20180424 / inductor_commercial_power_mlp2012_en.fm