DOCUMENT NUMBER NCD-4oB8-07
SAP-8 Series
Single-Mode
FC CONNECTOR PLUG
TECHNICAL SPECIFICATIONS
Seiko Instruments Inc.
OFC Division.
8, Nakase 1-Chome
Mihama-ku, Chiba-shi, Chiba-ken
261-8507 JAPAN
Telephone : +81-43-211-1211
Facsimile
: +81-43-211-8039
SAP-8 Series Single-Mode FC CONNECTOR PLUG
TECHNICAL SPECIFICATIONS
Document Number NCD-4oB8-07
NCD-4oB8-01
NCD-4oB8-02
NCD-4oB8-03
NCD-4oB8-04
NCD-4oB8-05
NCD-4oB8-06
NCD-4oB8-07
October 1994
January 1995
January 1996
June 1997
May 1998
April 2000
May 2003
Copyright 1994.1995.1996.1997.1998, 2000,2003 by
Seiko Instruments Inc.
All right reserved.
The information contained herein shall not reproduced or disclosed to any third party
without the express written consent of
SII.
The Specifications contained herein are subject to change without notice.
SII
is a trademark of
Seiko Instruments Inc.
Please address any questions, comments, and suggestions to:
Seiko Instruments USA Inc.
Electronics Components Division
2990 West Lomita Boulevard
Torrance, CA 90505, U.S.A.
Phone:
+1-310-517-7780
Facsimile:
+1-310-517-7792
Seiko Instruments GmbH
OFC Division
Siemensstraße 9b
D-63263 Neu-Isenburg, Germany
Phone:
+49-6102-297-0
Facsimile:
+49-6102-297-211
Seiko Instruments (H.K.) Ltd.
Sales Department
4th & 5th Floor, Wyler Center 2
200 Tai Lin Pai Road, Kwai Chung
N.T., Kowloon, Hong Kong
Phone:
+852-2421-8611
Facsimile:
+852-2480-5479
Seiko Instruments Taiwan Inc.
Sales Department
4F, No.40, Sec. 2, Min Chuan E. Rd.,
Taipei 104, Taiwan, R.O.C.
Phone:
+886-2-2563-5001
Facsimile:
+886-2-2521-9519
Seiko Instruments Singapore pte. Ltd.
Component Sales Department
2, Marsiling Lane,
Singapore, 739144, Singapore
Phone:
+65-269-1370
Facsimile:
+65-269-9729
ii
TABLE OF CONTENTS
Section
1.
PROVISION
1.1.
Application limit
2.
PARTS NUMBER
3.
GENERAL SPECIFICATIONS
3.1.
Parts and Materials
3.2.
Physical Dimensions
3.3.
General Tolerances
4.
PACKING
5.
NOTE
Page
1
1
1
2
2
2
3
3
3
Table
Table 1
Table 2
Table 3
Table 4
Parts number
Parts and materials
Parts and materials (Mainbody)
General tolerance
1
2
2
2
Figure
Figure 1 to 2 SAP-8 Connector
Figure 3 to 4 Mainbody
Figure 5 to 13
Part dimensions
4 to 5
6
7 to 9
iii
iv
1.
PROVISION
1.1
Application Limit
These specifications apply to the SAP-8 Single-Mode FC CONNECTOR PLUG supplied
by
SII.
2.
PARTS NUMBER
Parts number of the connector is shown in Table 1.
Table 1 Parts number
MODEL Number
TYPE Number
SAP-8
3 3 1 2 5 1 A 3 D 0
( Requied )
3 0 0 machining frame type
key-ring un-installed
Bulk packing
3 D 0 Molding frame type
Bulk packing
7 0 0 machining frame type
key-ring pre-installed
Bulk packing
0
1
3
5
0
1
3
6
9
Hood color
without hood
Black
White
Blue
Hood Inner Dia
without hood
0.9mm (non flamable)
3.0mm (Plastic)
2.0mm (Plastic)
0.9mm (Plastic)
Ferrule Inner Dia
S5 to S6
( 0.125 to 0.126mm )
Marking of Hood
0
1
Applicable Hood (mm)
without
0.9mm (non flamable)
SII Marking 0.9 to 3.0mm (Plastic)
1
A
Cap
Black PVC
Black Ferrule Cap
1
