0
R
CoolRunner XPLA3 CPLD
0
14
DS012 (v2.5) May 26, 2009
Product Specification
•
•
•
•
•
•
•
•
•
•
•
Available in commercial grade and extended voltage
(2.7V to 3.6V) industrial grade
5V tolerant I/O pins
Input register setup time of 2.5 ns
Single pass logic expandable to 48 product terms
High-speed pin-to-pin delays of 5.0 ns
Slew rate control per output
100% routable
Security bit prevents unauthorized access
Supports hot-plugging capability
Design entry/verification using Xilinx or industry
standard CAE tools
Innovative Control Term structure provides:
- Asynchronous macrocell clocking
- Asynchronous macrocell register preset/reset
- Clock enable control per macrocell
Four output enable controls per function block
Foldback NAND for synthesis optimization
Universal 3-state which facilitates "bed of nails" testing
Available in Chip-scale BGA, Fineline BGA, and QFP
packages. Pb-free available for most package types.
See
Xilinx Packaging
for more information.
XCR3256XL
256
6,000
256
7.0
4.3
4.5
154
18
Features
•
Fast Zero Power (FZP) design technique provides
ultra-low power and very high speed
- Typical Standby Current of 17 to 18
μA
at 25°C
Innovative CoolRunner™ XPLA3 architecture
combines high speed with extreme flexibility
Based on industry's first TotalCMOS PLD — both
CMOS design and process technologies
Advanced 0.35μ five layer metal EEPROM process
- 1,000 erase/program cycles guaranteed
- 20 years data retention guaranteed
3V, In-System Programmable (ISP) using JTAG IEEE
1149.1 interface
- Full Boundary-Scan Test (IEEE 1149.1)
- Fast programming times
Support for complex asynchronous clocking
- 16 product term clocks and four local control term
clocks per function block
- Four global clocks and one universal control term
clock per device
Excellent pin retention during design changes
•
•
•
•
•
•
•
•
•
•
Table 1:
CoolRunner XPLA3 Device Family
XCR3032XL
XCR3064XL
Macrocells
Usable Gates
Registers
T
PD
(ns)
T
SU
(ns)
T
CO
(ns)
F
system
(MHz)
I
CCSB
(μA)
32
750
32
4.5
3.0
3.5
213
17
64
1,500
64
5.5
3.5
4
192
17
XCR3128XL
128
3,000
128
5.5
3.5
4
175
17
XCR3384XL
384
9,000
384
7.0
4.3
4.5
135
18
XCR3512XL
512
12,000
512
7.0
3.8
5.0
135
18
Table 2:
CoolRunner XPLA3 Packages and User I/O Pins
XCR3032XL
44-pin VQFP
48-pin 0.8mm CSP
56-pin 0.5mm CSP
100-pin VQFP
144-pin 0.8mm CSP
144-pin TQFP
208-pin PQFP
256-pin Fineline BGA
280-pin 0.8mm CSP
324-pin Fineline BGA
1.
2.
3.
XCR3064XL
36
40
48
68
-
-
-
-
-
-
XCR3128XL
-
-
-
84
108
108
-
-
-
-
XCR3256XL
-
-
-
-
-
120
164
164
164
-
XCR3384XL
-
-
-
-
-
118
(1)
172
212
-
220
XCR3512XL
-
-
-
-
-
-
180
212
-
260
36
36
-
-
-
-
-
-
-
-
XCR3384XL TQ144 JTAG pins are not compatible with other members of the CoolRunner XPLA3 family in the TQ144 package.
Most packages are available in Pb-Free option. See individual data sheets for more details.
The 44-pin PLCC package is discontinued per XCN07022.
© 2000–2009 Xilinx, Inc. XILINX, the Xilinx logo, Virtex, Spartan, ISE, and other designated brands included herein are trademarks of Xilinx in the United States and other
countries. All other trademarks are the property of their respective owners.
DS012 (v2.5) May 26, 2009
Product Specification
www.xilinx.com
1
CoolRunner XPLA3 CPLD
R
Family Overview
The CoolRunner XPLA3 (eXtended Programmable Logic
Array) family of CPLDs is targeted for low power systems
that include portable, handheld, and power sensitive appli-
cations. Each member of the CoolRunner XPLA3 family
includes Fast Zero Power (FZP) design technology that
combines low power and high speed. With this design tech-
nique, the CoolRunner XPLA3 family offers true pin-to-pin
speeds of 5.0 ns, while simultaneously delivering power
that is less than 56
μW
at standby without the need for
"turbo bits" or other power down schemes. By replacing
conventional sense amplifier methods for implementing
product terms (a technique that has been used in PLDs
since the bipolar era) with a cascaded chain of pure CMOS
gates, the dynamic power is also substantially lower than
any other CPLD. CoolRunner devices are the only TotalC-
MOS PLDs, as they use both a CMOS process technology
and the patented full CMOS FZP design technique. The
FZP design technique combines fast nonvolatile memory
cells with ultra-low power SRAM shadow memory to deliver
the industry’s lowest power 3.3V CPLD family.
The CoolRunner XPLA3 family employs a full PLA structure
for logic allocation within a function block. The PLA provides
maximum flexibility and logic density, with superior pin lock-
ing capability, while maintaining deterministic timing.
CoolRunner
XPLA3
CPLDs
are
supported
by
Xilinx® WebPACK™ software and industry standard CAE
tools (Mentor, Cadence/OrCAD, Exemplar Logic, Synopsys,
Viewlogic, and Synplicity), using HDL editors with ABEL,
VHDL, and Verilog, and/or schematic capture design entry.
Design verification uses industry standard simulators for
functional and timing simulation. Development is supported
on multiple personal computer (PC), Sun, and HP plat-
forms.
The CoolRunner XPLA3 family features also include the
industry-standard, IEEE 1149.1, JTAG interface through
which boundary-scan testing, In-System Programming
(ISP), and reprogramming of the device can occur. The
CoolRunner XPLA3 CPLD is electrically reprogrammable
using industry standard device programmers.
Interconnect Array (ZIA). The ZIA is a virtual crosspoint
switch. Each function block has 40 inputs from the ZIA and
contains 16 macrocells.
From this point of view, this architecture looks like many
other CPLD architectures. What makes the CoolRunner
XPLA3 family unique is logic allocation inside each function
block, and the design technique used to implement product
terms.
Function Block Architecture
Figure 3
illustrates the function block architecture. Each
function block contains a PLA array that generates control
terms, clock terms, and logic cells. A PLA differs from a PAL
in that the PLA has a fully programmable AND array fol-
lowed by a fully programmable OR array. A PAL array has a
fixed OR array, limiting flexibility. Refer to
Figure 2
for an
example of a PAL and a PLA array. The PLA array receives
its inputs directly from the ZIA. There are 40 pairs of true
and complement inputs from the ZIA that feed the 48 prod-
uct terms in the array. Within the 48 P-terms there are eight
local control terms (LCT[0:7]) available as control signals to
each macrocell for use as asynchronous clocks, resets, pre-
sets and output enables. If not needed as control terms,
these P-Terms can join the other 40 P-Terms as additional
logic resources.
In each function block there are eight foldback NAND prod-
uct terms that can be used to synthesize increased logic
density in support of wider logic equations. This feature can
be disabled in software by the user. As with unused control
P-Terms, unused foldback NAND P-Terms can be used as
additional logic resources.
Sixteen high-speed P-Terms are available at each macro-
cell for speed critical logic. If wider than a single P-Term
logic is required at a macrocell, 47 additional P-Terms can
be summed in prior to the VFM (Variable Function Multi-
plexer). The VFM increases logic optimization by imple-
menting some two input logic functions before entering the
macrocell (see
Figure 4).
Each macrocell can support combinatorial or registered
logic. The macrocell register accommodates asynchronous
presets and resets, and "power on" initial state. A hardware
clock enable is also provided for either D or T type registers,
and the register clock input is used as a latch enable when
the macrocell register is configured as a latch function.
CoolRunner XPLA3 Architecture
Figure 1
shows a high-level block diagram of a 128 macro-
cell device implementing the CoolRunner XPLA3 architec-
ture. The CoolRunner XPLA3 architecture consists of
function blocks that are interconnected by a Zero-power
2
www.xilinx.com
DS012 (v2.5) May 26, 2009
Product Specification
R
CoolRunner XPLA3 CPLD
I/O
MC1
MC2
MC16
FUNCTION
BLOCK
40
40
FUNCTION
BLOCK
MC1
MC2
MC16
I/O
16
16
16
16
I/O
MC1
MC2
MC16
FUNCTION
BLOCK
40
40
FUNCTION
BLOCK
MC1
MC2
MC16
I/O
16
16
16
ZIA
16
I/O
MC1
MC2
MC16
FUNCTION
BLOCK
40
40
FUNCTION
BLOCK
MC1
MC2
MC16
I/O
16
16
16
16
I/O
MC1
MC2
MC16
FUNCTION
BLOCK
40
40
FUNCTION
BLOCK
MC1
MC2
MC16
I/O
16
16
16
16
DS012_01_112000
Figure 1:
Xilinx XPLA3 CPLD Architecture
PLA Array
Inputs
Outputs
PAL Array
Inputs
DS012_08_020601
Figure 2:
PLA and PAL Array Example
DS012 (v2.5) May 26, 2009
Product Specification
www.xilinx.com
Outputs
3
CoolRunner XPLA3 CPLD
R
8
Foldback NAND
(P
T
[8:15])
1
To Local Control Term (LCT0)
ZIA
Product
Term
Array
40 x 48
(P
T
0)
1
To Local Control Term (LCT7)
To Universal Control Term (UCT) Mux
(P
T
7)
40
(P
T
[32:47])
P-term Clocks
ZIA
ZIA
1
(P
T
16)
48
VFM
D
Q
I/O1
Macrocell 1
(P
T
[0:47])
ZIA
ZIA
1
48
(P
T
31)
VFM
D
Q
I/O16
Macrocell 16
(P
T
[0:47])
DS012_02_101200
Figure 3:
Xilinx CoolRunner XPLA3 Function Block Architecture
From P-term
To Combinatorial Path
and Register Input
From PLA OR Term
DS012_03_121699
Figure 4:
Variable Function Multiplexer
Macrocell Architecture
Figure 5
shows the architecture of the macrocell used in the
CoolRunner XPLA3 CPLD. Any macrocell can be reset or
preset on power-up. Each macrocell register can be config-
ured as a D-, T-, or Latch-type flip-flop, or bypassed if the
macrocell is required as a combinatorial logic function.
Each of these flip-flops can be clocked from any one of eight
sources or their complements. There are two global syn-
chronous clocks that are selected from the four external
clock pins. There is one universal clock signal. The clock
input signals CT[4:7] (Local Control Terms) can be individu-
ally configured as either a PRODUCT term or SUM term
equation created from the 40 signals available inside the
function block.
There are two muxed paths to the ZIA. One mux selects
from either the output of the VFM or the output of the regis-
ter. The other mux selects from the output of the register or
from the I/O pad of the macrocell. When the I/O pin is used
as an output, the output buffer is enabled, and the macrocell
feedback path can be used to feed back the logic imple-
mented in the macrocell. When an I/O pin is used as an
input, the output buffer is 3-stated and the input signal is fed
into the ZIA via the I/O feedback path. The logic imple-
DS012 (v2.5) May 26, 2009
Product Specification
4
www.xilinx.com
R
CoolRunner XPLA3 CPLD
clock input functions as the latch enable, with the latch
transparent when this signal is High. The hardwired clock
enable is non-functional when the macrocell is configured
as a latch.
mented in the buried macrocell can be fed back to the ZIA
via the macrocell feedback path.
If a macrocell pin is configured as a registered input, there is
a direct path to the register to provide a fast input setup
time. If the macrocell is configured as a latch, the register
Universal PST
CT [0:5]
To ZIA
PAD
To ZIA
From PT Array
1
48
PLA OR Term
VFM
PST
D/T/L Q
CT4
P-term
CLKEn
RST
To I/O
Global CLK
Global CLK
Universal CLK
P-term CLK
CT [4:7]
Universal RST
CT [0:5]
Note:
Global CLK signals come from pins.
ds012_05_122299
Figure 5:
XPLA3 Macrocell Architecture
I/O Cell
The OE (Output Enable) multiplexer has eight possible
modes (Figure
6).
When the I/O Cell is configured as an
input (or 3-stated output), a half latch feature exists. This
half latch pulls the input High (through a weak pull-up) if the
input should float and cross the threshold. This protects the
input from staying in the linear region and causing an
increased amount of power consumption. This same weak
pull-up can be enabled in software such that it is always on
when the I/O Cell is configured as an input. This weak pull
up is automatically turned on when a pin is unused by the
design.
The I/O Cell is 5V tolerant when the device is powered.
Each output has independent slew rate control (fast or slow)
which assists in reducing EMI emissions.
See individual device data sheets for 3.3V PCI electrical
specification compatibility.
Note that an I/O macrocell used as buried logic that does
not have the I/O pin used for input is considered to be
unused, and the weak pull-up resistors will be turned on. It
is recommended that any unused I/O pins on the CoolRun-
ner XPLA3 family of CPLDs be left unconnected. Dedicated
input pins (CLKx/INx) do not have on-chip weak pull-up
resistors; therefore unused dedicated input pins must have
external termination. As with all CMOS devices, do not
allow inputs to float.
V
CC
WP
To Macrocell / ZIA
From Macrocell
Slew
Control
GND
CT
Universal OE
V
CC
GND (Weak P.U.)
3
4
Weak Pull-up
OE = 7
I/O Pin
OE [2:0]
OE
Decode
0
1
2
3
4
5
6
7
I/O Pin
State
3-State
Function CT0
Function CT1
Function CT2
Function CT6
Universal OE
Enable
Weak P.U.
ds012_06_121699
Figure 6:
I/O Cell
5
DS012 (v2.5) May 26, 2009
Product Specification
www.xilinx.com
电子竞赛
