型号
  • 型号
  • 关键词
首页 > 器件类别 > 光电子/LED

GP1UX311QS

Infrared Receivers Remote Cont Rec 3V 38 kHz

器件类别：光电子/LED   

厂商名称：Sharp Microelectronics

下载文档
参数 预览 参数对比
GP1UX311QS 在线购买

供应商：

器件：GP1UX311QS

价格：-

最低购买：-

库存：点击查看

点击购买

器件参数
参数名称
属性值
Product Attribute
Attribute Value
制造商
Manufacturer
Sharp Microelectronics
产品种类
Product Category
Infrared Receivers
RoHS
Details
Carrier Frequency
38 kHz
Transmission Distance
8 m
High Level Pulse Width
1200 us
Low Level Pulse Width
1000 us
Minimum High Level Output Voltage
2.2 V
工作电源电压
Operating Supply Voltage
2.7 V to 5.5 V
工作电源电流
Operating Supply Current
270 uA
最大工作温度
Maximum Operating Temperature
+ 70 C
最小工作温度
Minimum Operating Temperature
- 10 C
封装 / 箱体
Package / Case
SIDE VIEW
高度
Height
7.5 mm
长度
Length
5.5 mm
宽度
Width
5.3 mm
安装风格
Mounting Style
Through Hole
工厂包装数量
Factory Pack Quantity
500
文档预览
GP1UX31QS Series
GP1UX31QS Series
Holder-less Type IR Detecting Unit
for Remote Control
■
Features
1. Holder-less shield case type.
2. Compact type.
3. Strengthened resistance to electromagnetic
induction noise by double mold method.
4. Operarting voltage 3V type.
■
Outline Dimens ions
(Unit : mm)
Conductive resin(GND)
5.5
2.1
3.2
7.5
6.9
1. AV equipments
2. Home appliances
3. Toys using IR sensor
+１
6.0
■
Applications
28
-
8.8
4.1
1.6
1.2
2.8
0.4
■
Absolute Maximum Ratings
Parameter
Symbol
Supply voltage
V
CC
*1
Operating temperature
T
opr
Storage temperature
T
stg
*2
Soldering temperature
T
sol
(T
a
=25℃)
Rating
Unit
V
0 to +6.0
℃
-10 to +70
-20 to +70
℃
265
℃
*1
*1
0.5
2.54
2.54
V cc
G ND
V out
Example of mounting drawing
from solder side (Reference)
Top of lenz
*1 No dew condensation is allowed
*2 For 6s (At mounting on PCB with thickness of 1.6mm)
2.54 2.54
1. *1 : Indicates root dimensions of connector.
2. Unspecified tolerance:±0.3
0.
8
Vout
GND
V
CC
■
Recommended Operating Conditions
Parameter
Supply voltage
Symbol
V
CC
Operating conditions
2.7 to 5.5
Unit
V
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: OP06013
1
3.9
3-
φ
GP1UX31QS Series
■
Model Line-up
Diversified models with a different B.P.F. frequency are also available.
B.P.F. center frequency
40
36
38
36.7
Model No.
GP1UX31QS
GP1UX310QS
GP1UX311QS
GP1UX312QS
Unit
kHz
■
Internal Block Diagram
R
L
V
OUT
Limiter
B.P.F. Demodulator Integrator Comparator
V
CC
GND
■Electro-optical
Characteristics
Parameter
Symbol
Conditions
(T
a
=25℃, V
CC
=3V)
MIN.
TYP.
0.27
MAX.
0.4
Dissipation current
High level output voltage
Low level output voltage
High level pulse width
Low level pulse width
B.P.F. center frequency
Output pull-up resistance
I
CC
V
OH
V
OL
T
1
T
2
f
0
R
L
No input light
*3
*3
-
V
CC
-0.5
I
OL
=1.6mA
*3
*3
-
600
400
-
-
-
-
*4
-
0.45
1200
1000
-
-
-
70
-
130
100
Unit
mA
V
V
μs
μs
kHz
kΩ
*3 The burst wave as shown in the following figure shall be transmitted by the transmitter shown in Fig. 1
The carrier frequency of the transmitter, however, shall be same as *4, and measurement shall be from just after starting the transmission until 50 pulse
*4 The B.P.F. center frequency f
0
varies with model, as shown in
■Model
Line-up
B urs t wave
600μs
1000μs
f
0
=(*4)
Duty 50%
Output s ignal
T2
T1
Sheet No.: OP06013
2
GP1UX31QS Series
■
Performance
Using the transmitter shown in Fig. 1, the output signal of the light detecting unit is good enough to meet the following items in the
standard optical system in Fig. 2.
1. Linear reception distance characteristics
When L=0.2 to 8.0m,
*5
E
V＜
10 lx and
φ=0°in
Fig.2, the output signal shall meet the electrical characteristics in the attached list.
2.Sensitivity angle reception distance characteristics
When L=0.2 to 6.0m,
*5
E
V＜
10 lx and
φ=30°in
Fig.2, the output signal shall meet the electrical characteristics in the attached list.
3.Anti outer peripheral light reception distance characteristics
When L=0.2 to 4.0m,
*6
E
V≦
300 lx and
φ=0°in
Fig.2, the output signal shall meet the electrical characteristics in the attached list.
*5 It refers to detector face illuminance
*6 Outer peripheral light source: CIE standard light source A shall be used and placed at 45°from perpendicular axis at the detector face center
Fig.1 Transmitter
20cm
PD49PI
10kΩ
10μF
5V
10kΩ
Transmitter (GL521 used)
f
0
(* 4)
Duty 50%
V
OUT
Oscilloscope
In the above figure, the transmitter should be set so that the output V
OUT (P-P)
can be 40mV.
However, the PD49PI to be used here should be of the short-circuit current I
SC
=2.6μA at E
V
=100 lx.
(E
V
is an illuminance by CIE standard light source A (tungsten lamp).)
Fig.2 Standard Optical System
Light detector face illuminance:E
V
V
OUT
Reception distance:L
Transmitter
(
φindicates
horizontal and vertical directions.)
Sheet No.: OP06013
3
GP1UX31QS Series
■
Precautions for Operation
1. When this infrared remote control detecting unit shall be adopted for wireless remote control, please use the following signal format .
 (NEC
code,RC-6code etc.)
・Total
duty ratio D
t
(Emitting time
 t
N
/ Transmitting time for 1 block T) : 40% or less.
Σ
N=1
n
・ON
signal time and OFF signal time
Supply Voltage
ON signal time per 1bit
OFF signal time per 1bit
V
cc
t
ON
t
OFF
2.7
to
3.0V
3.0 to 5.5V
200μs or more
400μs or more
300μs or more
Transmitting time for 1 block:T
T
ON
t
1
t
2
t
3
t
n
D
t
=(
Σ
t
N
/T)
×100 (%)
N=1
n
In case the signal format of total duty and/or ON/OFF signal time dosen`t meet the conditions noted above, there is a
case that reception distance much reduces or output dose not appear.
2. Use the light emitting unit (remote control transmitter), in consideration of performance, characteristics, operating conditions of
light emitting device and the characteristics of the light detecting unit.
3. Pay attention to a malfunction of the light detecting unit when the surface is stained with dust and refuse.
Care must be taken not to touch the light detector surface.
If it should be dirty, wipe off such dust and refuse with soft cloth so as to prevent scratch. In case some solvents are required, use
methyl alcohol, ethyl alcohol or isopropyl alcohol only.
Also, protect the light detecting unit against flux and others, since their deposition on the unit inside causes reduction of the
function, fading of markings such as the part number.
4. Unnecessary force shoud not be applied to terminal.
5. Do not push the light detector surface (photodiode) from outside.
6. To avoid the electrostatic breakdown of IC, handle the unit under the condition of grounding with human body, soldering iron, etc.
7. Since conductive thermo plasticity is used in 2nd mold regin,please be careful not to come in contact with PCB land
pattern.
8. External Circuit Examples (Mount the outer parts as near the unit as possible).
GND
V
CC
V
OUT
C
O
+
R
1
GND
V
e
V
O
(Circuit parameters)
R
1=
47Ω±5%
C
1=
47μF
In setting R
1
and C
1
, use suitable values after considering under the real condition
The circuit constant is a example. It is difference from mounting equipment. Please select it by your mounting equipment.
This device has a transistor as protection element between V
CC
and GND to improve anti-static electricity proof.
Please be carefully not to apply exceeding the absolute maximum ratings of applying voltage and continuous high voltage spike
noise because there is cases that transistor will be short by secondary breakdown generally. In order to do difficultly, Please add CR
filter(47Ω(1/10W), 10μF or more)such as external circuit example above near V
CC
.
Sheet No.: OP06013
4
GP1UX31QS Series
9. There is a possibility that noise on output may be caused by environmental condition (Disturbing light noise, Electromagnetic
noise, Power supply line noise, etc.) even if there is no input transmission signal.
10. Please shall confirm operation or your actual machine. Because the output pulse width of this product is fluctuated by
environmental conditions such as signal format, temperature, distance from transmitter, and so on.
11. In case that this product is kept in high humidity condition, it may be hard to solder, please be careful enough about storage
method.
Depend on the flux you select, there are different solderabilities, so please select a suitable flux and use it.
12. This product dose`t correspond to soldering by reflow.
13. Please make sure in case pf hand soldering that yue the solder iron with less than 45W power and solder iron point(edge)
temperature is less than 320℃ within 3 seconds,and also don't add any force to lead frame directly.And please make sure never
to touch 2nd mold resin by a solding.
14. When using this device,please be careful not to cause dew drop.
Be aware that the dew drop rusts lead pins portion and others, may affect the electric characteristics.
15. The lead flame may be deformed since the device is packed in vinyl bag.
Sheet No.: OP06013
5
查看更多>
参数对比
与GP1UX311QS相近的元器件有：GP1UX31QS、GP1UX317QS、GP1UX310QS。描述及对比如下：
型号 GP1UX311QS GP1UX31QS GP1UX317QS GP1UX310QS
描述 Infrared Receivers Remote Cont Rec 3V 38 kHz Infrared Receivers Remote Cont Rec 3V 40 kHz Resin only Infrared Receivers Rem Cont Rec Infrared Receivers Remote Cont Rec 3V 36 kHz
制造商
Manufacturer		 Sharp Microelectronics Sharp Microelectronics Sharp Microelectronics Sharp Microelectronics
产品种类
Product Category		 Infrared Receivers Infrared Receivers Infrared Receivers Infrared Receivers
工厂包装数量
Factory Pack Quantity		 500 1 500 500
Product Attribute Attribute Value - Attribute Value Attribute Value
RoHS Details Details Details -
Carrier Frequency 38 kHz 40 kHz - 36 kHz
High Level Pulse Width 1200 us 1200 us - 1200 us
Low Level Pulse Width 1000 us 1000 us - 1000 us
Minimum High Level Output Voltage 2.2 V 2.2 V - 2.2 V
工作电源电压
Operating Supply Voltage		 2.7 V to 5.5 V 2.7 V to 5.5 V - 2.7 V to 5.5 V
工作电源电流
Operating Supply Current		 270 uA 270 uA - 270 uA
最大工作温度
Maximum Operating Temperature		 + 70 C + 70 C - + 70 C
最小工作温度
Minimum Operating Temperature		 - 10 C - 10 C - - 10 C
高度
Height		 7.5 mm 7.5 mm - 7.5 mm
长度
Length		 5.5 mm 5.5 mm - 5.5 mm
宽度
Width		 5.3 mm 5.3 mm - 5.3 mm
非易失性MRAM存储是否适合用于ADAS 安全系统存储
在无人驾驶技术成为各大厂商的追求目标时，ADAS高级驾驶辅助可以说是他们追逐道路上的第一步。主要是...
英尚微电子 汽车电子
eZ430-CHRONOS 4折优惠 有需要的筒子不要错过啦
前一段时间出现在欧冠决赛上面的GoalControl-4D手表出尽了风头，大家一致认为其和TI的...
buer1209 微控制器 MCU
【IoT毕业设计】树莓派开发板+机智云IoT+监测机器人
摘要: 以小车为基底，以树莓派开发板为中心，搭载摄像头、传感器等数据采集设备...
毛球大大 RF/无线
如何对USB摄像头进行视频捕捉
目前正在学习关于摄像头捕捉的相关技术 分别采用VFW 和DirectShow 实现了视频图像的捕捉...
sunling8412 嵌入式系统
菜鸟提问 ：直接修改PCB中的net的信号属性?
在allrego PCB editor 是否可越过修改电路原理图，不再导入网表而直接修改PCB中的...
feaven PCB设计
谁做过摩托车射灯驱动的？联系我707320742,需要方案或者IC
谁做过摩托车射灯驱动的？联系我707320742,需要方案或者IC 谁做过摩托车...
QWE4562009 电路观察室
热门器件
热门资源推荐
基于嵌入式汽车行驶记录仪的设计与实现 期刊论文：改进多尺度融合结合小波域HMT模型的遥感图像分割 mp3键盘驱动源码,同时支持滚动和按键两种方式 基于A3992和C8051F300的两相步进电机驱动系统(含电路图). 基于视觉技术集成的车辆防错系统开发及应用 开关变换器中滑模控制技术研究 嵌入式LinuxBasicV3_0 WCDMA室内覆盖综合解决方案 航运订票系统：若剩余票数足够, 则可以进行直接订票, 若不够可进行 自动驾驶的多传感器融合
新手上路 怎么设置SysTick的优先级的啊？求救啊 不仅仅用于摄像，无人机的另类玩法 请教STC单片机timer0和PCA模块的问题！ 【一起玩esp8266】板子收到，上电测试 win ce下能做作语音识别开发吗，有没有什么好的开发包推荐。 一个牛人对模拟电路的理解(转) xilinx ISE中文注释 分支预测（bi-mode yags预测原理） 32位RISCCPU---ARM芯片的应用和选型(2)
简洁的过零调功器电路设计与分析 单稳态控制电路设计与分析 光控电路设计与分析 永不缺相启动运行的电动机控制电路 IGBT模块通过控制门极阻断过电流 MT3608构成3.7V转12V的升压电路图 运算放大器IC741的基本工作原理及在电路中的实现方式 比较常见的功率整流器和滤波电路 一个简单的红外耳机电路 基于TDA1554的立体声放大器电路
器件捷径:
E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ
需要登录后才可以下载。
登录取消