GPC130D4,GPC130D4 pdf中文资料,GPC130D4引脚图,GPC130D4电路-Datasheet-电子工程世界

文档预览

GPC130 GLOBAL PERFORMANCE SWITCHERS

FEATURES:

• Wide-range AC input 85-264VAC

• 2-year warranty

• Approved to UL1950, IEC950, EN60950 and CSA22.2-

234 L3

• Exceeds FCC and CISPR22 Class B conducted

emissions requirements

• Multiple outputs

• For medical version, see p. 92

marked to LVD

•

GLOBAL PERFORMANCE SWITCHERS

SPECIFICATIONS:

AC Input

85-264Vac, 47-63Hz single phase.

Input Current

Maximum input current at 120Vac, 60Hz with full rated output load: 3.5A

Hold-Up Time

20mSec minimum from loss of AC input at full load, nominal line (115Vac).

Output Power

100W continuous, 165W peak; 130 with 26 cfm air flow. Peak ratings are

for 60 sec. maximum duration, 10% duty cycle. During peak load

condition, output regulation may exceed total regulation limits.

Overload Protection

Fully protected against short circuit and output overload. Short circuit

protection is cycling type power limit on outputs 1 & 2; foldback type on

outputs 3 & 4. Recovery after fault is automatic. See output ratings chart

for additional notes or conditions.

Overvoltage Protection

Main outputs: 124%

12% typical.

Efficiency

70% at full rated load, nominal input voltage, depending on model and

load distribution.

Turn-on Time

Less than 1 second at 120VAC, 25°C (inversely proportional to input

voltage and thermistor temperature).

Input Protection

Internal AC fuse provided. Designed to blow only if a catastrophic failure

occurs in the unit.

Inrush Current

Inrush is limited by internal thermistors. Inrush at 240VAC under cold start

conditions will not exceed 34A.

Temperature Coefficient

0.03%/ºC typical on all outputs.

Environmental

Designed for 0 to 50°C operation at full rated output power; derate

output current and total output power by 2.5% per

°C

above 50°C. See

Environmental and Packaging Specifications (p. 11) for additional

information.

Power Fail

TTL- or CMOS-compatible output goes low (< 0.5V) 5mSec before

output voltage drops more than 4% below nominal voltage upon loss of

AC power. The signal is factory set to trip on 84 to 94VAC brown-out

depending upon incoming line impedance and distortion. Other settings

are available to the user through adjustment of built-in potentiometer

(consult factory for assistance).

No-Load Turn-on/Standby

No degradation of reliability will occur.

Output Noise

0.5% RMS, 1% Pk-Pk, 20MHz bandwidth, differential mode. Measured

with noise probe directly across output terminals of the power supply.

Transient Response

Main output—500µSec typical response time for return to within 0.5% of

final value for a 50% load step change.

∆i/∆t<0.2A/µSec.

Maximum

voltage deviation is 3.5%. Startup/shutdown overshoot less than 3%.

Remote Sense

Provided as a standard feature on output 1.

Voltage Adjustment

Built-in potentiometer adjusts voltage

±5%

on outputs 1 & 2.

Reverse Voltage Protection

All outputs protected against inadvertent application of reverse voltage up

to 1 times rated current of the reverse output.

Overload Protection

Factory set to begin power limiting at approximately 170W.

EMI/EMC Compliance

All models include built-in EMI filtering to meet the following emissions

requirements:

EMI SPECIFICATIONS

COMPLIANCE LEVEL

Conducted Emissions

EN55022 Class B; FCC Class B

Static Discharge

EN61000-4-2, 6 kV contact, 8 kV air

RF Field Susceptibility

EN61000-4-3, 3 V/meter

Fast Transients/Bursts

EN61000-4-4, 2 kV, 5 kHz

Surge Susceptibility

EN61000-4-5, 1 kV diff., 2 kV com.

Leakage Current

0.7mA. 254Vac @ 60Hz input.

Safety

Approved to UL1950, CSA22.2 No. 234 Level 3, IEC950 and EN60950.

UL file #E135803 commercial; CSA #LR46516 all models. The output(s)

are intended for safety earthed Signal Output and Intermediate Circuits

only. All DC outputs are SELV under normal and single fault conditions.

Condor D.C. Power Supplies, Inc./A subsidiary of SL Industries, Inc.

2311 Statham Parkway, Oxnard, CA 93033 • 800-235-5929 • 805-486-4565 • FAX 805-487-8911 • www.condorpower.com/

Model

GPC130A

Output No.

Output

+5V

+12V

-12V

+12V

+ 5V

+12V

-5V

-12V

+5V

+12V

-15V

+15V

+5V

+24V

-12V

+12V

+5V

+24V

-15V

+15V

Output

Minimum

Output

Maximum (B)

16A

1.2A

16A

1.2A

16A

1.2A

16A

3.5A

1.2A

16A

3.5A

1.2A

Output

Maximum (C)

20A

1.2A

20A

1.2A

20A

1.2A

20A

3.5A

1.2A

20A

3.5A

1.2A

Output Peak

25A

1.5A

25A

1.5A

25A

1.5A

25A

1.5A

25A

1.5A

Noise P-P

50mV

120mV

50mV

120mV

50mV

120mV

50mV

120mV

150mV

50mV

240mV

120mV

50mV

240mV

150mV

Total

Regulation (A)

GPC130B

GPC130C

GPC130D

GPC130E

A. Total regulation is defined as the maximum deviation from the nominal voltage for all steady-state conditions of initial voltage setting, input line voltage and output load.

B. Unrestricted natural convection cooling.

C. Requires 26cfm moving air.

GPC130 MECHANICAL SPECIFICATIONS:

INPUT:

J1:

AMP P.C.B. HEADER P/N 640445-5

8.50 [215.90mm]

8.000 [203.20mm]

PIN 1)

PIN 2)

PIN 3)

AC LINE

N/C

AC NEUTRAL

AC LINE

AC NEUTRAL

AC GROUND

N/C

+ SENSE

- SENSE

POWER FAIL

PIN 4)

PIN 5)

N/C

AC GROUND

MATING CONNECTOR AMP P/N

HOUSING 640250-5

CONTACTS 770522-1

TB1:

[32.46

0.51]

1.278

0.20

TB1

OUT 2

V.ADJ

TB2

0.375 X 6-32 TERMINAL BLOCK

PIN 1)

PIN 2)

PIN 3)

PIN 1)

PIN 2)

PIN 3)

PIN 4)

SIGNALS:J2

1.944

[49.38mm]

AMP P.C.B. HEADER P/N 640456-4

4.50

[114.30mm]

OUT1

V.ADJ

MATING CONNECTOR AMP P/N 640440-4

OUTPUT:

J3:

AMP P.C.B. HEADER P/N 1-640445-6

PIN 1)

PIN 2)

PIN 3)

PIN 4)

PIN 5)

PIN 6)

PIN 7)

PIN 8)

OUTPUT #4

OUTPUT #3

OUTPUT #2

COMMON

PIN 9)

PIN 10)

PIN 11)

PIN 12)

PIN 13)

PIN 14)

PIN 15)

PIN 16)

COMMON

OUTPUT #1

6-32 MTG

(0.125 [3.18mm] MAX SCREW PENETRATION)

4 PLCS

0.25

[6.35mm]

PF ADJ

6-32 MTG

4 PLCS

0.12 [3.05mm]

MATING CONNECTOR AMP P/N

HOUSING 1-640250-6

CONTACTS 770522-1

2.00

[50.80mm]

[32.46

0.51]

XFMR (T3) PROTRUDES

IN THIS AREA ONLY.

1.278

0.20

TB2:

0.375 X 6-32 TERMINAL BLOCK

PIN 1)

PIN 2)

PIN 3)

PIN 4)

OUTPUT #4

OUTPUT #3

OUTPUT #2

COMMON

PIN 5)

PIN 6)

PIN 7)

PIN 8)

COMMON

OUTPUT #1

OPTIONAL COVER AVAILABLE, ORDER P/N 08-30466-1130

OPTION: ADD "-T" SUFFIX TO PART NUMBER FOR

6-32 SCREW TERMINAL BLOCK ON I/O

WEIGHT: 2.3 LBS MAX. [1.05 kg]

TOLERANCES: X.XX=0.030 [0.76mm]

X.XXX=0.010 [0.25mm]

Condor D.C. Power Supplies, Inc./A subsidiary of SL Industries, Inc.

2311 Statham Parkway, Oxnard, CA 93033 • 800-235-5929 • 805-486-4565 • FAX 805-487-8911 • www.condorpower.com/

GLOBAL PERFORMANCE SWITCHERS

型号	GPC130D4	GPC130A4	GPC130A3	GPC130A1	GPC130B2	GPC130B4	GPC130B3	GPC130D1	GPC130D3
描述	Power Supply Module	Power Supply Module	Power Supply Module	Power Supply Module	Power Supply Module	Power Supply Module	Power Supply Module	Power Supply Module	Power Supply Module
Reach Compliance Code	unknown	unknown	unknown	unknown	unknown	unknown	unknown	unknown	unknown
厂商名称	SL Power	-	-	-	SL Power	SL Power	SL Power	SL Power	SL Power