CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3.
θ
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 5V Supply
Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 5),
Unless Otherwise Specified
TEST CONDITIONS
TEMP
(°C)
(NOTE 6)
MIN
TYP
(NOTE 6)
MAX
UNITS
PARAMETER
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
ON Resistance, R
ON
Full
V+ = 4.5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V,
(See Figure 5)
V+ = 5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V
25
Full
25
Full
V+ = 5V, I
COM
= 1.0mA, V
NO
or V
NC
= 1V, 2V, 3V
V+ = 5.5V, V
COM
= 1V, 4.5V, V
NO
or V
NC
= 4.5V, 1V,
(Note 7)
V+ = 5.5V, V
COM
= 4.5V, 1V, V
NO
or V
NC
= 1V, 4.5V,
(Note 7)
V+ = 5.5V, V
COM
= 1V, 4.5V, or V
NO
or V
NC
= 1V, 4.5V,
or Floating, (Note 7)
Full
25
Full
25
Full
25
Full
0
-
-
-
-
-
-0.1
-5
-0.1
-5
-0.2
-10
-
19
23
0.8
1
7
0.01
-
-
-
-
-
V+
30
40
2
4
8
0.1
5
0.1
5
0.2
10
V
Ω
Ω
Ω
Ω
Ω
nA
nA
nA
nA
nA
nA
R
ON
Matching Between Channels,
∆R
ON
R
ON
Flatness, R
FLAT(ON)
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
COM OFF Leakage Current,
I
COM(OFF)
COM ON Leakage Current,
I
COM(ON)
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V
NO
or V
NC
= 3V, R
L
=1kΩ, C
L
= 35pF, V
IN
= 0 to 3V,
(See Figure 1)
V
NO
or V
NC
= 3V, R
L
=1kΩ, C
L
= 35pF, V
IN
= 0 to 3V,
(See Figure 1)
R
L
= 300Ω, C
L
= 35pF, V
NO
= V
NC
= 3V, V
IN
= 0 to 3V,
(See Figure 3)
C
L
= 1.0nF, V
G
= 0V, R
G
= 0Ω, (See Figure 2)
R
L
= 50Ω, C
L
= 5pF, f = 1MHz, (See Figure 4)
R
L
= 50Ω, C
L
= 5pF, f = 1MHz, (See Figure 6)
25
Full
25
Full
Full
25
25
25
-
-
-
-
3
-
-
-
28
40
20
30
10
3
76
-105
75
150
50
100
-
5
-
-
ns
ns
ns
ns
ns
pC
dB
dB
Turn-OFF Time, t
OFF
Break-Before-Make Time Delay
(ISL5122, ISL5123), t
D
Charge Injection, Q
OFF Isolation
Crosstalk (Channel-to-Channel)
4
FN6022.6
November 17, 2004
ISL5120, ISL5121, ISL5122, ISL5123
Electrical Specifications - 5V Supply
Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 5),
Unless Otherwise Specified
(Continued)
TEST CONDITIONS
R
L
= 50Ω, C
L
= 5pF, f = 1MHz
TEMP
(°C)
25
25
25
25
25
(NOTE 6)
MIN
-
-
-
-
-
TYP
60
8
8
21
28
(NOTE 6)
MAX
UNITS
-
-
-
-
-
dB
pF
pF
pF
pF
PARAMETER
Power Supply Rejection Ratio
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7)
COM OFF Capacitance,
C
COM(OFF)
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7),
ISL5120/1/2
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7),
ISL5123
POWER SUPPLY CHARACTERISTICS
Power Supply Range
Positive Supply Current, I+
V+ = 5.5V, V
IN
= 0V or V+, all channels on or off
Full
Full
2.7
-1
0.0001
12
1
V
µA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Input Voltage High, V
INH
Input Current, I
INH
, I
INL
NOTES:
4. V
IN
= input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25°C.
