The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
Note 2:
V
S
is the voltage observed/applied at either the A or B Ports across
the switch.
Note 3:
The input and output negative voltage ratings may be exceeded if
the input and output diode current ratings are observed.
Note 4:
Unused control inputs must be held HIGH or LOW. They may not
float.
DC Electrical Characteristics
Symbol
V
IK
V
IH
V
IL
I
I
I
OZ
R
ON
Parameter
Clamp Diode Voltage
HIGH Level Input Voltage
LOW Level Input Voltage
Input Leakage Current
OFF-STATE Leakage Current
Switch On Resistance
(Note 6)
V
CC
(V)
4.5
4.0–5.5
4.0–5.5
5.5
0
5.5
4.5
4.5
4.5
4.0
I
CC
∆
I
CC
V
IKU
Quiescent Supply Current
Increase in I
CC
per Input
Voltage Undershoot
5.5
5.5
5.5
20
20
20
20
26
27
28
30
2.0
0.8
±1.0
10
±1.0
38
40
48
48
3
2.5
−2.0
T
A
= −40 °C
to
+85 °C
Min
Typ
(Note 5)
Max
−1.2
Units
V
V
V
µA
µA
µA
Ω
Ω
Ω
Ω
µA
mA
V
0
≤
V
IN
≤
5.5V
V
IN
=
5.5V
0
≤
A, B
≤
V
CC
V
IN
=
0V, I
IN
=
64 mA
V
IN
=
0V, I
IN
=
30 mA
V
IN
=
2.4V, I
IN
=
15 mA
V
IN
=
2.4V, I
IN
=
15 mA
V
IN
=
V
CC
or GND, I
OUT
=
0
One Input at 3.4V
Other Inputs at V
CC
or GND
0.0 mA
≥
I
IN
≥ −50
mA
OE
1,2
=
5.5v
Note 5:
Typical values are at V
CC
=
5.0V and T
A
= +25°C
Note 6:
Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the
voltages on the two (A or B) pins.
Conditions
I
IN
= −18
mA
3
www.fairchildsemi.com
Preliminary
FSTU162211
AC Electrical Characteristics
T
A
= −40 °C
to
+85 °C,
Symbol
Parameter
C
L
=
50pF, RU
=
RD
=
500Ω
V
CC
=
4.5 – 5.5V
Min
t
PHL
, t
PLH
t
PZH
, t
PZL
t
PHZ
, t
PLZ
Propagation Delay Bus to Bus
(Note 7)
Output Enable Time
Output Disable Time
1.5
1.5
Max
1.25
6.0
7.0
V
CC
=
4.0V
Min
Max
1.25
6.5
7.2
ns
ns
ns
V
I
=
OPEN
V
I
=
7V for t
PZL
V
I
=
OPEN for t
PZH
V
I
=
7V for t
PLZ
V
I
=
OPEN for t
PHZ
Figures 2,
3
Figures 2,
3
Figures 2,
3
Units
Conditions
Figure
Number
Note 7:
This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical On
Resistance of the switch and the 50pF load capacitance, when driven by an ideal voltage source (zero output impedance).
Capacitance
Symbol
C
IN
C
I/O
(Note 8)
Parameter
Typ
3
6
Max
Units
pF
pF
Conditions
V
CC
=
5.0V
V
CC
, OE
=
5.0V
Control Pin Input Capacitance
Input/Output Capacitance
Note 8:
T
A
= +25°C,
f
=
1 MHz, Capacitance is characterized but not tested.
Undershoot Characteristic
Symbol
V
OUTU
Parameter
Output Voltage During Undershoot
Min
2.5
Typ
V
OH
−
0.3
Max
Units
V
Conditions
Note 9:
This test is intended to characterize the device’s protective capabilities by maintaining output signal integrity during an input transient voltage under-
概述 TFT（Thin Film Transistor）LCD即薄膜场效应晶体管LCD，是有源矩阵类型液晶显示器（AM-LCD）中的一种。 液晶平板显示器，特别TFT-LCD，是目前唯一在亮度、对比度、功耗、寿命、体积和重量等综合性能上全面赶上和超过CRT的显示器件，它的性能优良、大规模生产特性好，自动化程度高，原材料成本低廉，发展空间广阔，将迅速成为新世纪的主流产品，是21世纪全球经济增...[详细]
工控电子
